Jump to content
SAU Community

It's all right for tonight, cruising in a corvette and feeling alright!


Recommended Posts

haha, well considering the engine is being pulled it wont be available. Damn baffled sumps! :D. Anyway, CES fitted mine and just used 2 normal 2.5" cats and tilted them sideways to fit, not sure if this picture shows it properly though. The bar only melts when I go to the track, cause it is such a big heavy exhaust, when doing serious corners it must press against the side of the gap for the zaust. You mustn't be driving hard enough eh?? hehe, jokes :Pimp2:

  • Replies 100
  • Created
  • Last Reply

Top Posters In This Topic

haha, well considering the engine is being pulled it wont be available. Damn baffled sumps! :). Anyway, CES fitted mine and just used 2 normal 2.5" cats and tilted them sideways to fit, not sure if this picture shows it properly though. The bar only melts when I go to the track, cause it is such a big heavy exhaust, when doing serious corners it must press against the side of the gap for the zaust. You mustn't be driving hard enough eh?? hehe, jokes :Pimp2:

LoL, i drive it hard.. jus never had a chance to take it on the tracks yet.. Have you dynoed it after you put on the zaust? i got 215kw@all4s with just the zaust and pods (stock boost). I thank the zaust for the good power. Also what dump pipes do u have? Im still using the stock dumps.

LoL, i drive it hard.. jus never had a chance to take it on the tracks yet.. Have you dynoed it after you put on the zaust? i got 215kw@all4s with just the zaust and pods (stock boost). I thank the zaust for the good power. Also what dump pipes do u have? Im still using the stock dumps.

I got 197awkw on the mercury motorsport dyno with just the exhaust and a nismo panel filter(stock boost also). Still got the stock dumps for the minute, but one of the things going in atm is a pair of hks dumps to finish the exhaust. I am interested to see what, if any, difference they make.

but one of the things going in atm is a pair of hks dumps to finish the exhaust.  I am interested to see what, if any, difference they make.

the wastegate sound will be louder i know that much. it should also give it a diffrent tone. those stock dumps are shocking, i cant belive i had stock dumps at 300awkw. when they pulled the stock dumps off i couldnt belive how badly they reduce in size :O

CES make there own dumps, thats where i got mine from n e way. just make sure u get the HPC coated ones.

i think they were around $900

give them a call.

check out there website

http://www.cesracing.com.au/

the hks dumps actully go down in size at the bottom of the pipe which is STUPID !!! why o why would they do that ??? doesnt make sence,

thats why i went the CES ones they were bigger than the HKS DUMPS and arrived the same day i ordered them :O

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...