Jump to content
SAU Community

Recommended Posts

Well not actually the engine itself.

Last night I went to adjust the boost a little on my little boost controller (the one mark sells on here) and split the hose.

Thought no worries. Replaced the hose but when I took the car for a drive it made a weird "whurling" type noise with any ammount of boost pressure. To me sorta sounds like a air leak but not sure< is that what noise it would make if a cooler hose blew off?

Even with the hose removed it still makes the same noise.

I thought I might have tore a little hole in one of the pipes from the afm to the turbos but they all seem ok, removed the clamps etc and checked under there.

Anyone know what it could be?

Link to comment
https://www.sau.com.au/forums/topic/75736-rb26-making-weird-noise/
Share on other sites

argghhh. hope its not one of the gaskets.

car still runs fine, it will make boost but seems to be down a little bit on power. the noise also seems to go away after around 3000rpm, sort of when the turbos really start spooling.

most likely one of the turbo gaskets? would it be a head gasket? what are the symptoms of that?

it sounds like a ghost comin from my engine bay. can really only hear it from 2000-3000 revs under load, even coming off load from about 5000revs you cant hear it again till it comes down to 3000 or so again.

Im guessing its one of the turbo gaskets? maybe to the manifold. Surly someone knows what it is. Car still drives fine and comes on boost fine.

it sounds like a ghost comin from my engine bay. can really only hear it from 2000-3000 revs under load, even coming off load from about 5000revs you cant hear it again till it comes down to 3000 or so again.

Im guessing its one of the turbo gaskets? maybe to the manifold. Surly someone knows what it is. Car still drives fine and comes on boost fine.

Ive had something very similar in my R32, ended up being a gasket just off the turbo..

Gaskets.JPG

Ive had something very similar in my R32, ended up being a gasket just off the turbo..

Its quite common for the bolts on the "Twin Turbo" pipe to work loose, particularly for the rear turbo, and the gasket to blow. Unfortunately they are not a standard gasket so you have to get them from Nissan AFAIK (or as I did, make them).

I currently have a high-pitched leak somewhere (plus backfiring) and I am pretty sure its the same gasket. :(

Lucien.

thanks champs, ill swap them next week and see how it goes. I hope its just one of them so the turbos dont have to come out.

Can I buy just those 4 gaskets or do I have to buy the whole set from nissan?

also will the leak cause any damage or is it still ok to go boosting it a little for normal driving?

Its three gaskets, and Nissan doesn't do turbo gasket sets anymore, so you just order in the three.

Before you do though, better to check that's what is actually causing the problem. The recommendation I have seen lately is to mix up some detergent with water and put it in a spray bottle. Spray all the possible connections, fiddle with the throttle to rev it a bit, and look for the bubbles.

Hard to say if it will cause any damage without knowing exactly what/where it is. At a guess, probably not, but it will throw the mixtures out as air is escaping.

LW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Some troubleshooting, connect up a timing light/gun with a proper ignition lead on coil 1. Hold the revs at 4~4500rpm and see if your timing is all over the shop, scattering off its tits. If so, there's a high chance your CAS is fked. But I read you have a Link ECU ready to go in, why not just skip all this and put that in - will make troubleshooting so much easier.  
    • Misfires when the car is fully warm are generally attributed to the coils (and/or the igniter, on cars with a separate igniter). They can stop working properly when they get hot for a number of reasons. Either electric/electronic, or from thermal expansion opening up gaps and allowing HV leakage. Seeing as you have replaced the coils, that could/should rule them out. But I wouldn't always assume so. Were the coils genuine? Or is there a chance you have bought some counterfeit Chinesium shit? Then we're back onto loom connections. They can fail when warm/hot for the same reasons. Inspections, cleaning of contact surfaces, ensuring that terminals are fully inserted, etc etc, are all justified. The same (heat effects) holds true for the other electrics and their connectors. AFM & CAS, primarily. If you try that Chinesium AFM, drive it around on low load until it is properly hot, but do'nt give it more load than you have to, except when you need to see if it will still miss. I'm dead serious about the untrustworthiness of the calibration of those copy AFMs. Injectors are unlikely to get hot unless the fuel is coming back around hot. You could try squirting them with compressed air or freeze spray to cool them back down to see if they are maybe the cause.
    • Alright, all the plugs looks good. Noticed that it starts to get bad when the car is up to temp, that's when things starts to misfire hard. next to do is Injector cleaning and such. Got in touch with a shop to do work on the injectors next Monday also help on diagnosis.
    • House of Fatz dry dock needs a clean sadly one of the long time stables is leaving this weekend   see ya mr purple
    • Hence why I've only modified my car into a pure daily. Everything has to remain reliable & roadworthy, while providing value and grin factor. It also must not be handcrafted to the extent that the car will be immovable if something breaks because you cannot get or make a replacement to at least limp around with.
×
×
  • Create New...