Jump to content
SAU Community

Removing the front bar on R33 SII

Blitz

By Blitz,
in Exterior & Interior Styling

 Share

Recommended Posts

Blitz Grand Master

Blitz

Posted
Posted

Anyone here taken the front bar of a R33 series 2 GTST?

I am planning on starting to fit my FMIC on the weekend and just wondering if there is anything i should know prior to removing the front bar.

Do the headlights need to be removed to undo the bar?

How many bolts hold the bar in place and where are they located?

Thanks all

:P

Link to comment
https://www.sau.com.au/forums/topic/761-removing-the-front-bar-on-r33-sii/
Share on other sites
EDS33T Enthusiast

EDS33T

Posted
Posted

Nick,

-First pull out the grille (5 plugs)

-below the grille there's three scrivets that hold the bar to the metal subframe, there's also one underneath the centre scrivet, just behind the number plate

-Behind the plastic inner wheel arch guard there's two screws either side which hold the sides of the bar to the front of the guards.

-The headlights don't need to come out

-Don't forget to disconnect the fog lights/blinkers

-It should come straight off.

The bar is easily cut with a jigsaw with a metal blade if the back of the bar needs to be cut forward to fit an FMIC in. I'm pulling mine off this weekend to check the my crash repairers handywork and try and line things up a bit better.

Ed

Blitz Grand Master

Blitz

Posted
  • Author
Posted

EDS: thanks for the info.... just what i was after :)

My cooler is 600 X 300 X 75 - have you fitted one to your car yet?

Im hoping to have the piping this week so I can start fitting

Jimbo: i will get some pics for you while i install if you like :)

EDS33T Enthusiast

EDS33T

Posted
Posted

Nick,

I had a Hyperflow FMIC the same size you've got in about this time last year, but had to pull it out cause it made the motor boil sitting in traffic in early september:(

The mods I had to make were cutting a hole for the pipework under the washer bottle and modifying the front of the chassis rail with a hammer:D

Ed

EDS33T Enthusiast

EDS33T

Posted
Posted

If I was moving over 70kph in any heat I'd have no problem, but once I was sitting in traffic, the temp almost went off the scale!

The intake air going through an FMIC is cooler for sure, but being a heat exchanger the air coming in the front of the car gets heated, then hits the air-con, gets heated further, by that time the radiator's got no hope.

Most people don't have any trouble at all. Maybe I had one of the thermo's wired up backwards?:uh-huh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...