Jump to content
SAU Community

***FOUND!!! 666DAN Dark Blue R34 Coupe***


Recommended Posts

umm.. have you told police that it might have those plates on it? if these guys really are that dumb, and the plate 584IPT is actually registered to them, ask for the police to run a check to see whos name its in and what car they drive, it's a small chance, but hey it can't hurt.

  • Replies 124
  • Created
  • Last Reply

Top Posters In This Topic

umm.. have you told police that it might have those plates on it? if these guys really are that dumb, and the plate 584IPT is actually registered to them, ask for the police to run a check to see whos name its in and what car they drive, it's a small chance, but hey it can't hurt.

these plates could have been reported stolen to the police off another car and the police told "dan" that the plates have been reported stolen and maybe on his car. (from around the same area that his car was taken).

Will keep a look out also. I did see a Dark Blu R34 headed South along Gympie Rd Kedron last week around 4:45pm. Don't know if it was yours or not was in far left lane, light was fading and it was moving pretty quick. Just down from the Dept of Emergency Services building where i work.

Will keep a look out also. I did see a Dark Blu R34 headed South along Gympie Rd Kedron last week around 4:45pm. Don't know if it was yours or not was in far left lane, light was fading and it was moving pretty quick. Just down from the Dept of Emergency Services building where i work.

umm, it was stolen this week mate

Will keep a look out also. I did see a Dark Blu R34 headed South along Gympie Rd Kedron last week around 4:45pm. Don't know if it was yours or not was in far left lane, light was fading and it was moving pretty quick. Just down from the Dept of Emergency Services building where i work

That was me though

Well if they are stupid enough to keep driving it, and just change the plates, then they could well be stupid enough to go down BWCP or at least head down that way. So eyes will be out for sure.

Sorry to hear mate....but which side of Brisbane was it stolen from???

Coz I almost had my R33 stolen the other nite when I leave my car outside my house....lucky my dogs keep barking then wake me up....I jumped into the car and chased them and called the police as well....It was a group of fuc*head driving a old Ford shit-box....and finally the policeS stopped them on the ipswich road near red bank plaze...

Fu*K those asshole who cant afford one but want to steal one!

try checking out or letting the wreckers or jap parts ppl know to let you know if anyonne comes in tryin to sell them R34 Parts??? badluck n sorry to hear that .. hope u find it soon !! will keep an eye out

Car has been located by a forum member buying parts, waiting to get the info to pass onto the police.

good to hear dan. hope ya lead turns out to be a true 1. maybe not the best idea to post up yet until the cops are on to it bcoz they mite read this.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...