Jump to content
SAU Community

Recommended Posts

Hi,

Ive got a manual 34 with turbo back 3" exhaust, apexi pod, hks bov, avcr (0.7 bar) and power fc. The mods were fitted in this order first exhaust > pod > avcr > pfc.

After I had the Power FC tuned I was slightly dissapointed with the 'increase' in power (it was tuned on the road, not a dyno by chapman & chapman). Since then I haven't been too worried about it as the car is running perfectly, and the tuner had ironed out a 'miss' I had on idle and some backfiring between gears caused by the atmo bov. It was only today that I realised my car is hardly any quicker than a standard manual sedan (judging purely by 'feel').

Just now i swapped back to my standard computer and it doesn't really feel hardly any slower..... I am going to run it on a dyno -

My question is how much power (at least) should I expect?

Dan666 was also in my car and agreed it should be a lot quicker......

Any ideas??

Cheers, Paul

Link to comment
https://www.sau.com.au/forums/topic/76608-r34-performance-issues-with-pfc/
Share on other sites

Hmmm - cheers bass i'll see how I go.

By the way I ran 13.9 @ 101mph with 2.21 60 foot - That was a 3500 launch (obviosuly not dropping the clutch) and it was on 19" chromes with 235's. Also remember its a sedan... Bass - how did you get a 1.9 60 foot?

I was quite happy with this time - although shoudl i expect more? I think the sedan is at least 150kg heavier than the coupe?

Your missing a fmic.......

I went through the same thing in my car......I got the PFC by necessity as my afm stuffed up and I decided to get a z32 and pfc while I was at it.

I had pretty much the same mods, exhaust, pod, blitz ID3, z32 and pfc.

Have to admit the pfc DID make a little bit of difference but not as much as I expected, but once the front mount was installed and the pfc had a bit more room to do its magic it made a HUGE difference.

Admittedly the dyno is a bit of a happy dyno...but the difference the fmic should be legit as it was done on the same dyno...

I ended up going from 183rwkw before fmic to 220rwkw after fmic.

  • 2 weeks later...

I got a front mount installed a few days ago. The car is alot quicker all the way through the revs. I can't belive it actually seems to have less boost lag - theres alot more response all the way through the revs. It actually felt 'doughy' before, now it feels almost like 2 people have got out of the car. It hasn't been retuned yet, i'm not sure how much would have to be adjusted with just the addition of an intercooler... it will be done this week some time.

I've driven a fair few cars (mainly 32's and 33's) with bigger front mounts and the same mods as mine minus the computer and really have felt hardly quicker than cars with stock coolers... maybe r34's with better breathing on the intake and exhaust and tighter a/f ratios really put alot more pressure on the stock cooler??

Either way i'm happy :P I'll get a dyno readout in a while and let you know - i'd be happy with anything over 190kw...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
×
×
  • Create New...