Jump to content
SAU Community

Recommended Posts

Hi gang,

Wondering if anyone's experienced the same problem that I'm having. The gist of it is that every time I turn my ignition to the "ON" position, I'm hearing a clicking sound (like two bits of plastic hitting together). It seems to be coming from behind the centre air vents (listening closely to it, it sounded like a solenoid or something that have springs or moving parts). Anyway, the sound stops after a minute or so. While it doesn't affect the performance of the car, and I know that it's not serious, I still would like to get to the bottom of it. Yesterday (monday) I removed the plastic section around the centre consoles of the dash and checked if it could have been some loose wire making the sound but thatwasn't the source of the sound. I haven't got the nerve to remove the whole dash to find out whats making the sound. Any help with a solution, or some tips on removal of the whole dash would be helpful. BTW, the sound seem to be coming from behind the firewall (ie, it's not in the engine bay).

Cheers,

J

Hey dude, my R33 has the same problem and it is actualy comming from the air conditioner motar. Mine has had the problem on and off for 4 years now comming and going randomly. It has not affected the climate controll in anyway it's just been an anoying sound for the first minute or so when you start the car. I asked a mech about it and he said that it would cost $350 for a new motar. Since it doesnt affect it in anyway I have just left it. I've never had a second opinion so he might just be trying to rip me off. Might be worth looking into. He said it was something catching on a fan inside the motar that makes the clicking noise.

Its actually only a $160 part from nissan - an actuator that opens/closes a vent. But you have to pull your whole dash out to get to it, it sits on top of the heater box. I've replaced mine.

Allow 2-4 hours to pull out dash and replace the part and replace dash if you want to do it.

mate my sky does the same thing. comes and goes for the past 18mths. as ferni says above its just a matter of being bothered with the dash or putting up with the click.

i know of at least another two guys that have had the same problem.

I c..I c....well, thanks 4 all the feedbacks guys...much appreciated.

If it's a common thing, I think I might just leave it. As a number of you have already pointed out, it's more of an annoyance than a performance issue. The thing is, I'm looking to sell my car..( and i'm hearing "oh goshhh...wtf 4..etc... :D "..i know I know...anyway, I just want a quick sales coz i'm thinking of going oversea, and the only thing wrong with the car is that noise, so I was hoping to fix it up, so that prospective buyers will have less things 2 nit pick ova...I've already done the 100K service..so that's one less hassle outa the way. Once again, thanks for the feedbacks guys...

Cheers,

J

Just dont turn the climate control on when you're selling it. sorted :) I only just bought my skyline and have the exact same thing going on. Or just be straight up and tell em it's a common prob. I have this and my heater not working - turns out that's a common problem too!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...