Jump to content
SAU Community

Recommended Posts

hey people i need some advice,

i have a rb20det 5 spd in my S13 silvia....

tonight all of a sudden it started rumbling and it sounded exactly like a WRX boxer engine. it was making normal boost levels but the power felt lower and it was very lumpy!!!! i pulled over and had a look under the bonnet, when i gave the throttle a little twist, i could hear a sound like a hiss. i couldn't destinguish if it was an air leak or if it was like a squirting sound. (if you understand me?) but the sound was around the top of the engine where the intake pipe meets the throttle body. is this a common problem some people have heard? or will it be something to go see a doctor about???

after i stopped after and turned off the engine for 30 mins it was fine again. then it happened for about 5 minutes while driving home. what is thisssssss?????

any help would be appreciated.

Link to comment
https://www.sau.com.au/forums/topic/77208-rb20det-problem-wrx-sound/
Share on other sites

Dead coil pack dude! Guarentee it. Take off the plug cover and unplug each one individually. The engine will run even rougher on each one. When you unplug the one that makes no difference you've found the stuffed one :D

Mine did this when I imported it and as soon as it got warm the dodgy one would fail.

good luck.

I had the same problem but it was a spark plug,the ceramic bit above the gap cracked and slid down to cover the spark gap.Everynow and then it would back to normal,must of been the comp pushing it back up etc.

So yer as baselinez said coil pack coz it's not sparking.

Also spray carby clean around the inlet manifold(where the top/bottom meets)join and see if the idle changes.Could be gasket or maybe just tighting of the bolts.

I have had this problem many times and had many reasons for it.

As mentioned it could be a faulty plug or a faulty ignition coil or module. It can also be caused by a leak in the inlet tract.

As you heard a hissing sound around the throttle area I would be starting there first and looking closely at the rubber joiner for a split.

And while you have the crossover pipe off may as well throw in some new plugs.

Its gotta be ignition.

Mine comes and goes just like that on my RB26. Seriously just goes into Rexy mode, then 5mins later, goes to GTR mode. (GTR is better by the way, hehe).

It has to be ignition, because if it was a cracked seal or something it would be more constant, I think mine might even be the plug going into the module, hope its not a coil pack.

will a dud coil pack come and go though? cause today the problem seemed not existent. but i bet it'll go on the weekend again. also just noticed my clutch is starting to get very slippery, so thats more money i have to spend. is the RB sound really worth it in the end??? i'm thinking maybe an SR would have been the better option :D

just like almost the majority of contributors on this thread, i say that it is you coils. get them replaced.

(quote:'m thinking maybe an SR would have been the better option ) believe me, the RB is way better!

Dude, its basically the only problem the RBs have and its just due to age. Yes with my car the problem came and went until it stayed stuffed for good.

Do the test and it will prove if its them or not.

You can't blame a slipping clutch on the motor type :D Its just one of those things. Stick with it, the RB shits on the SR. One dud coil is the only problem i've had on mine in 6 months since I imported it. Fix it and you'll be fine! Keep us posted!

lol that was what i was like too, i was like: "hey cool i sound like a modded WRX!" then i started driving like miss daisy and worrying about it hahahah but i enjoyed the sound but not the rumble through the car etc.

i will try to suss out the coil packs on the weekend, and get back to you's!

Anyone?

Can you tell us how to test each coil?

Because if its going to be a matter of trialing each coil being swapped over, it could take 3 months, as its inconsistant whether it works or not. So I'll swap one, then wait a week, then swap the next one, wait another week or two and so on.

There must be some way to test.

Like he said, just unplug them one by one, if the one you unplug is GOOD the car will sound even WORSE, so plug it back in and move on to another until you get to one that when unplugged makes no difference, that's the cylinder that's down.

But don't just assume it's the coil, pull the spark plug out and check it (is if fouled? clean it and see if things improve), swap a pack around and see if the dropped cylinder follows the coil, if not to loom could be damaged, etc.

If it's a dud coilpack buy a new one, or if you intend to run high-boost in the future maybe think about a set of SplitFires (~$650).

I say again:

Because if its going to be a matter of trialing each coil being swapped over, it could take 3 months, as its inconsistant whether it works or not. So I'll swap one, then wait a week, then swap the next one, wait another week or two and so on.

This is relevant because the guy the started the thread and myself are NOT having the problem all the time, but would like to fix it before it comes an ALL THE TIME thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...