Jump to content
SAU Community

Recommended Posts

Strut Bar / Strut Tower Brace - New

To suit:

r32 skyline (front and rear)

s13 silvia/180sx (front and rear)

S14 & S15 200sx (front only)

I'm looking into getting R33 and R34, if you are interested PM me and i'll send out a group PM when I can get them.

PM to order

strutbar1.JPG

$69 each

($138 front & rear)

-Tim

Link to comment
https://www.sau.com.au/forums/topic/77338-strut-bars-front-rear-cheap-69-each/
Share on other sites

for me, they made a big difference, rear end used to be a bit unpredictable due to relatively soft coilovers, and since i've had the rear strut brace in it's helped that a lot. I've noticed especially when drifting, weight transitions on corners where you change direction have been a lot more smooth than it used to be.

sorry to be a hassle mate, but would you be able to take a pic of how much height clearance you get over the plenum/throttle intake. I've got an rb25 in my 32 and its hard to find a strut brace with enough clearance.

Thanks

Oh, and i'll grab a rear brace too..!

http://i2.photobucket.com/albums/y19/merli...e/IM000026s.jpg

http://i2.photobucket.com/albums/y19/merli...e/IM000027s.jpg

http://i2.photobucket.com/albums/y19/merli...e/IM000028s.jpg

http://i2.photobucket.com/albums/y19/merli...e/IM000029s.jpg

by the looks of things there is ok clearance. take note of where the actual bar runs in realtion to the intake piping before the manifold (in 3rd pic) - as in the case of the rb20 the bar is to the side of intake pipe, (not directly above it).

There seems to be plenty of clearance over engine and at least one inch clearance from rb20det intake manifold. No idea how high rb25det manifold sits.

The only suggestion I can make is perhaps use washers on the drivers side to increase the height of the bar. This is quite safe as long as you don't run out of thread on the strut top bolt's.

Hope this helps, PM me if you wish to order and I'll send bank account details.

-Tim

cool, thanks for that.

only strut bar that has trouble fitting, is the S13 one with a CA18DET as the rocker cover is slightly too high. It can be fixed by using washers to space one side up a bit.

  • 4 weeks later...
Merlin you need to become a registered trader if you wish to continue trading here.

Please PM me for more information

PM sent,

I have one pair of r32 left, I'm no longer selling these.

-Tim

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...