Jump to content
SAU Community

Recommended Posts

Hey Guys

Brought this in for myself but need cash now.

1993 R32 V-spec (brembos, etc)

Advan wheels

R33 N1 engine

HKS twin BOVs

Greddy intercooler and piping

Recaro seats

Boost controller

Body kit

Bonnet

And other mods

Looking for 31.5K and need substantial deposit to secure the car.

Cheers

Michael 0414561121

Link to comment
https://www.sau.com.au/forums/topic/78755-1993-r32-v-spec-with-n1-engine/
Share on other sites

Do you have any recent pics? (ie; since it's been in Aust?)

The car is about to be complied so it looks pretty much like this now. Have ordered new bumper and car will be cleaned up appropriately.

Guest DIRTgarage
The car is about to be complied so it looks pretty much like this now. Have ordered new bumper and car will be cleaned up appropriately.

Obviously didn't read the question...read it again and answer please....is this car in Aust....and if so can we have some pics

Can you confirm if the car has been resprayed as the black engine bay concerns me

All 32 GTR's have black engine bays... if the engine bay is body colour, it means the car has been resprayed.

Incorrect.

Im yet to see a white R32 GTR that doesnt have a black engine bay (with the exception of those that have been resprayed). And yes these cars have white colour code listed on the build plate.

Im yet to see a white R32 GTR that doesnt have a black engine bay (with the exception of those that have been resprayed). And yes these cars have white colour code listed on the build plate.

For the record I have seen at least 4 factory white GTR's with colour coded engine bays and the same with silver.

Though to my knowledge the blue, wine red, black and gunmetal R32's did have a black engine bay standard.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...