Jump to content
SAU Community

Recommended Posts

Hi,

I'm reasonably new at all of this under the bonnet stuff and, not meaning to sound too stupid, was wondering if someone could help me with what I think is a mis-firing problem.

Sometimes, at around 2000-2500 rpm my R33 seems to momentarily splutter a little and then continue ok. It happens both accelerating and decelerating. :)

Is this symptom of a misfire?

If it is, what is the step-by-step process to check and (if needs be) replace my spark plugs? I've searched "misfire" and "spark plugs" on the forum but there's no step-by-step process for novices like me. :D

Or can my problem be a symptom of something else?

My 1993 R33 is basically stock. Just a 3.5" exhaust from the cat out.

I've only had it for 3 weeks :P and it's done 88000 kms so I had the timing belt, all other belts and water pump done. I don't know if the plugs have been replaced so that's what's got me think about them as the source of my problem.

I can't remember if I had the problem before the work was done because I was too busy giving it a bit of heavy right-foot work. :D

Anyway, any help would be greatly appreciated.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/8008-misfire-maybe-spark-plugs/
Share on other sites

dlskip,

If it was a misfire then I would normally expect it to be higher in the rev range 5-6000rpm, and it would normally be on acceleration only. Do you have and aftermarket computer?

If you've only had it 3 weeks then it should be under warranty, if you bought it from a yard, just ask them to have a look at it.

Otherwise my suggestion is to get it on a dyno, it should only take 1/2-1hour to determine what the problem is, and then you won't have to loose sleep over it.

Good luck.

See'ya:burnout:

Thanks for the quick replies.

raist60:

The problem only happens on light to medium acceleration.

It otherwise idles beautifully.

It also only happens randomly, always between 2000-2500 rpm. It just kind of "hiccups", if you know what I mean.

GTS-t VSPEC:

I don't have an aftermarket computer.

I also didn't the car from a yard, so it looks like I'm on my own for this one. :)

In terms of dyno-testing, how much does it usually cost?

Thanks guys.

i was also wondering about this same sort of thing....mine is fine while acc and decellerating, but just idleing it ''hicups'

however when idling it idles at about 1500-2000 is this to low....

when i had a service done...we incountered a rob which could be my prob...if so i need some advise

when we were changing the plugs...we changed all of them except the on right in the middle under the tubing or something, we were both pulling on the socket tool thing but could not budge the damn plug without snapping the plug......the guy put some sh*t on the plug and said hopefully next time this stuff would losen it up

I dont know if this will help or not but when i first got my r32 the car yard filled it with normal feul and it was back firing and miss firing. When i put optimax and or BP premuim not a problem.

Dont know if that will help

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...