Jump to content
SAU Community

200sx question

whiteknight
 Share

Recommended Posts

jazza08 Mentor

jazza08

Posted
Posted

Well any model GTST that has steel wheels (think r32 might) can run higher boost, the other GTST turbos (33/34) have ceramic turbos which means that it will crack under to much boost... not sure what wheels the t28s have and not sure whats safe on them, generally dont have to many kms on these units so can run higher boost through them anyway :)

Its not to do with the b/b or bush bearing nature of the turbo, its to do with the compressor/exhaust wheels on them :P

Someone feel free to correct me if im wrong?

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

TTT Grand Master

TTT

Posted
Posted
Well any model GTST that has steel wheels (think r32 might) can run higher boost, the other GTST turbos (33/34) have ceramic turbos which means that it will crack under to much boost... not sure what wheels the t28s have and not sure whats safe on them, generally dont have to many kms on these units so can run higher boost through them anyway :P

Its not to do with the b/b or bush bearing nature of the turbo, its to do with the compressor/exhaust wheels on them :P

Someone feel free to correct me if im wrong?

As usual, I'll correct you.

R32 - R34 GTST/GTT all have Ceramic exhaust wheels.

R33 series II and R34 GTT have a form of plastic Compressor wheel (the wheel on the front on the air filter side of the turbo)

I believe the R32 GTR also has ceramic exhaust wheel. not sure about R33 GTR.

that is why people tend to upgrade to N1 turbo's which are steel wheel.

R32 GTST - R34 GTT (all single turbo skylines) all have Ball Bearing turbo's.

Whitenight - no.. it does not mean you can get 225rwkw out of a T28 from an S15 when on a skyline.

The S15 turbo will be a downgrade to the RB25 stock turbo.

it is smaller and will flow less.

it is also a different bolt pattern which would require more mods to fit.

S15 turbo's are good upgrades for CA18's or SR20's from the S13 range.

and usually also go good for those that Turgo charge their 4agze which is the 1.6L supercharged toyota engine.

jazza08 Mentor

jazza08

Posted
Posted

You need to get over urself mate :P

I have seen a dyno of 215rwkw on an s15 with a t28 b/b turbo, also did have cams and on an rb25 it may make more power due to the engine... but thats really really at the max of the turbo mate, its not usual to see that kind of figure!

jazza08 Mentor

jazza08

Posted
Posted

What you believe as a correct fact in regards to a WRX vs R33 could also be regarded as incorrect unless you have both cars in stock standard form to compair?

Do you think you can stop laying into me about trying to help, its not as if i said this is how it is hints y i asked for any1 to correct me which you wanted to do in a smart ass manner... wouldn't of said anything if you would of said 'actually Jazza r32s also have ceramic turbo's' instead of ill correct you again.

Dont think im asking too much to not get attitude do you?

scathing Grand Master

scathing

Posted
Posted
Scathing -  

yeh that would be Brentons right?

I think he had in the region of 225 rwkw with a lot of other mods apart from the turbo.

Scathing, if you are the same scathing on other forums, then you'll know Dale.

and I think that night you were hitting 14 flat in the tree fiddy... if that is you..

Yep, and yep.

Very unimpressed with my ET. There's definitely more in the car, but after I set the 14 flat I just got a little too excited trying to break my NA light-tune barge into the 13's, and ended up screwing up the next couple of launches.

I figured you were talking about Dale before. The other thing about Dale's car is that his suspension is set up for the track. He did soften the dampers out and run lower-than-normal pressures, but the rest of the geometry is still very circuit oriented.

And he was using the D01J's which, with their ultra-stiff sidewalls, aren't the best drag tyre in the world.

TTT Grand Master

TTT

Posted
Posted

the only time I got down there, it was a good day.

Greg (not old man but the other one... Sellby I think it is (the suspension dude)) was there and he helped out a few of us first timers.

anyway, after a few soggy laps in my S14 with S15 stock suspension, I parked it and went for a drive with Dale.

after seeing/feeling the way his car taking the corners with the teins and DJ01's, I didn't take my car back out.. I was quite scared being in his car and the corner speed and late braking that he could do.

Brenton was there and he put on a set of yokahama slicks.

hahahaha

I had asked him to take me for a spin in his at lunch, but after experiencing what Dales car co do with less power (he had his boost controller down to 11psi) and with just semi slicks, I chickened out of a ride with brenton..

hahahahaha

fsmout Collaborator

fsmout

Posted
Posted

Yeah s14 i would say 170rwkw to 180rwkw and a 1/4 mile in the mid to high 13's...just my 2 cents

My mate has these mods and dynoed 160rwkw but that dyno reads 10% low, so it will also depend on the dyno you get the reading from, gear, tyre psi and dyno mode etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...