Jump to content
SAU Community

Recommended Posts

Hey guys, I know this must have been covered a thousand times, but i couldnt find the answers i was looking for, so i thought i would try again.

I'm looking at dropping an R33 box in to my R32, but I don't know were to take it to get the conversion,

I understand I Need a custom Tail Shaft, a different Speedo Cable, and a modified or custom cross member,.

Correct me if I'm wrong on any of the things above, or if I have missed anything, But where in Adelaide would I take my car for this sort of work???

Does a R33 box bolt on to the engine the same, does it have the same shaft pattern???

Any help would be greatly appreciated.

Thanks guys

Magik32

Greg

Link to comment
https://www.sau.com.au/forums/topic/81933-r33-box-in-to-my-r32/
Share on other sites

ure going to need a GTR speed sensor and a custom gearbox mount.

R33 gearboxes run via an electronic sensor (or something electronic), whereas the RB20 gboxes are mechanical.

They're not easy to find - i've been looking for months and haven't found one yet.

If anyone can point me in the direction of one - please do!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...