Jump to content
SAU Community

Recommended Posts

Well not quiet cause im already here, but my car will be here soon. I've booked it on the India Pacific as its the cheapest way i could find to get it over and should be arriving on the 10th of next month (fingers crossed i don't get bumped)

Appart from just being excited to see my car again, had to tell someone even if i don't know anyone here yet :P I was more interested to see if anyone had experiance with shipping there car by train? Anything I should be watching out for? I've already checked that Just Car will cover it while its in Transit and NRMA home and contents cover all the stuff i have chucked in it while in transit :)

Link to comment
https://www.sau.com.au/forums/topic/81967-tragic-arrives-in-nsw/
Share on other sites

Its not too low, setup for handling rather then looks :D however... i have kinda piled all my stuff in it :D The good thing is my brother is required to drive it onto the train so atleast i know someone won't be doing a 4k launch up the ramp and riping out all my piping. He will have to have someone follow him there so he can get home so if its over loaded hopefully he can remove some of the stuff...

I sent my car from Sydney to Perth by train in 1995 and it was a nightmare.

Firstly some a$$wipe drove the car 85km and thrashed the guts out of it as it had used over a 1/4 tank of fuel and 1lt of oil.

I had the car carrier company charged with auto theft and threatened to sue them. They paid over $5k damages as the whole exhaust and chassis rail had deep gouges (car was lowered). The clutch and fanbelts were rooted, but the car was never the same after it was repaired. I felt violated, but I got justice.

I had used a car carrier from door to door, but it was handled by 3 different companies under contract.

If you are in control of the car, I would think it will be fine, but just make sure you keep the keys. I have heard that a few thefts from the cars does happen, so do not pack the car with valuables.

I ended up sending the car back via TNT road and had no issues, except it needed a good wash.

  • 2 weeks later...

Well she arrived yesturday, all in one piece and not a scratch on her. Gave it a wash and she's shining now.

Didn't have any problems with the service i even had all my TV's / Stereo's in the rear seat and nothing was touched.

First thing i noticed driving in NSW around my area (Mosman) is the roads suck ass. I'd have to say WA roads are on average about 2000% better from my limited driving knowledge in Syd.

So watch out people there is a crazy WA driver on the roads...

Well she arrived yesturday, all in one piece and not a scratch on her. Gave it a wash and she's shining now.

Didn't have any problems with the service i even had all my TV's / Stereo's in the rear seat and nothing was touched.

First thing i noticed driving in NSW around my area (Mosman) is the roads suck ass. I'd have to say WA roads are on average about 2000% better from my limited driving knowledge in Syd.

So watch out people there is a crazy WA driver on the roads...

hahahaha

wanna go out for a cruise tonite?

First thing i noticed driving in NSW around my area (Mosman) is the roads suck ass. I'd have to say WA roads are on average about 2000% better from my limited driving knowledge in Syd.

Mosmon roads are bad??

pft... wait to you try our good old Parramatta rd.

You'll love it.

Well she arrived yesturday, all in one piece and not a scratch on her. Gave it a wash and she's shining now.

Didn't have any problems with the service i even had all my TV's / Stereo's in the rear seat and nothing was touched.

First thing i noticed driving in NSW around my area (Mosman) is the roads suck ass. I'd have to say WA roads are on average about 2000% better from my limited driving knowledge in Syd.

So watch out people there is a crazy WA driver on the roads...

Welcome to Sydney.

GTST is right Mosman bad? LOL try goin North as well :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...