Jump to content
SAU Community

Recommended Posts

So hey Rezzinator all those Pics (you know the ones  :( ) that I have of you, what do I do with them? now that you`ve lost you job a cant bribe you!!

You still have them??? Oh shiiiiiiit... :O

By the way, yesterday I was blown away by your generosity Terry and I had a really good time (kicking your ass around the pool table was a highlight B) ) hahaha. I won't forget it mate and when I'm in a position to do the same I will.

Dude thats fine, I dont expect anything back, did it because I wanted to. Hey btw I think the Skyline would be a better buy than the silvia. Bit of a rarer car, already Turbo, hasnt got some poxy brown interior .I also think if you can afford it go up on the price.

"Dude your inbox must be full cant send you this"

Well it is a Zenki S14, very early one (non ABS)

It has quite a lot of bits on it, all of which were put on before I got it.

3-core radiator

Oil Cooler

S15 Engine

S15 BB turbo

Equal length manifold (so it sounds nice)

Engine damper thingo

Some exhaust

GReedy Intercooler with custom steel piping and no BOV for flutter action

Z32 AFM

Apexi AFC (all set to Zero, but I am 99% sure it has a chipped ECU)

HKS EBC-III switched off so I run 0.7bar

Water temp and boost gauges

Apexi pen turbo timer

Silk Road coilovers F:10kg R:8kg but they seem quite nice

2-way LSD

S15 rear subframe

2x BBS LM 17x9+20 wheels

4x Stern R16 17x9+24 wheels

2x Enkei RP-01 17x9+22 wheels

I run 20mm spacers on the rear and 13mm on the front

Currently I am using 235/45 fronts and 235/40 rears

I have some 215/45 tyres ready to go as the rears are finished now.

Honda NSX yellow

Some front bar thing

Kouki taillights

Flared rear wheel arches and rolled front guards

Punch Koala stickers also a Kangaroo road sign sticker

HID headlights

Momo Race steering wheel

75mm steering wheel spacer

Recaro reclinable seat (which is way too high)

Handbrake button thing

That is all I can remember, I should work it out fully one day.

post-662-1123221759.jpg

post-662-1123222028.jpg

post-662-1123222109.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...