Jump to content
SAU Community

Recommended Posts

Hi

I've trawled the internet and can't seem to find anywhere that sells the Greddy single turbo inlets for Rb26.

The one that allows you to run two airflow meters off the one single turbo. You usually see them on T78s etc.

Anyone know where to buy them from, and what are they called exactly?

I have attached a pic:

http://www.members.shaw.ca/ssbperformance/...ns/RB26DETT.jpg

Cheers :P

Link to comment
https://www.sau.com.au/forums/topic/82426-greddy-single-turbo-inlet-rb26/
Share on other sites

I got mine mage custom. for a little sum of money out of alloy, for twin 80mm afm.

I'll know in about a week if I'm going to persist with the current set up, as I have max out the afm as in another thread, might go autronic after all the rooting around.

I got mine made custom. for a little sum of money out of alloy, for twin 80mm afm.

I'll know in about a week if I'm going to persist with the current set up, as I have max out the afm as in another thread, might go autronic after all the rooting around. If you are interested I will post up or send pic.

mmmm - ah OK Sean - you convinced me ya silver tongue devil - djetro it is then!

i fitted mine on a new engine never started it fired first kick and idled.

so far with a light tune it drives sweet . give it a week or 2 for run in and ill give you the full run down.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to find reliable dyno results that help my selection   Thinking G30- 660 twin scroll 1.06   Problem is my current setup isn't imo terrible. This is the genuine flog it at the track tune so there is a few kws in it but pulled for track safety   Non VCT RB25DE home built and has baby 256 Poncams, 60mm throttle body. 90mm exhaust and decent ARC cooler with Emtron KV8 Would like to break 400rwkws on 20psi and want a bit more through the 4,000rpm range. New setup needs to beat attached dyno
    • Hey y'all, had some bad ball joints in my tie rods, so figured i'd just replace both inners and outers.  Went with the high-misalignment system from GKTech. My car's lowered so figured why not. M14 Super Adjustable Inner Tie Rod High misalignment S13 240sx/S14/S15/Skyline tie rod ends (12mm/14mm) Welp, took over a week to get the job done, but finally did. Took it on the maiden voyage today and... - The OE boots do not sit properly on the new inner tie rods - If you look at the photo in the link above, new ITRs are basically threaded all the way through the length of them, so best I could do was tighten the boot down with a screw-down hose clamp onto the ITR's threads. - There is a "whoosh"ing sound every time I turn the steering, seems like it could be coming from the air moving into/out of boots. Concerning, bc it'll likely pull in nasty shit from the outside when I turn... namely thinking of moisture. - Looking at the rack from the back of the car, under it, the left tie rod is straighter than the right. Right droops down a bit. - My alignment is way outta wack, that's expected. Taking it to get an alignment as soon as I can. - The big thing is that the steering isn't really "springing" back like it used to. Wondering if there's something tied to pressurization of the system that I managed to f**k up. This was supposed to be a 20 min job... why doesn't anything ever go right with these cars?
    • Thanks guys, toruqed down to 65ft-lb, or 88 n-m.  Now have other problems, will chronicle in another thread. You guys are the best, thanks for all the ugga duggas.
    • R serious becoming more of a weekend cars or collectors cars there are less on the road these days , but you sometimes come by one or two . we might have to start spotting the V serious to make up for the gap.  
×
×
  • Create New...