Jump to content
SAU Community

Recommended Posts

Engine pretty much same... RB25

The main difference is in in the turbo between series 1 and series 2. The standard series 2 turbo has a plastic wheel turbo and hence can handle less horsepower then the series 1 ceramic.

Interior specs are different. To me series2 looks a bit more modern with more modern looking trim, but its fairly cosmetic and the front bar and bonnet looks slightly different. Airbag, drivers side airbag and ABS came a bit more standard on the series 2. Series 2 headlights are darker tint.

Otherwise they are fairly similar in terms of gearbox, diff, power, reliability, etc.

m spec question has been asked many times before... do a search

Thanks guys

damm right about the newbie, went for my first drive in one on Sunday, after checking out modifed 180sx etc ... previously owned turbo fours and a rotary .....

Really enjoy the ride and potential of the R33 .... have started pricing some goodies at JMS to help with the choices

There are quite a few cosmetic differences between the two:

- Different headlights (much better!)

- front bar with round indicator and spotlight (series 2)

- Dash fascia has rough finish rather than smooth for series 1

- Rear 'SKYLINE' lettering on bootlid is in same colour as car for series 2, as opposed to in clear plastic for series 1

- Higher boot spoiler on series 2, although did come out on '95 model series 1.

- Interior cloth trim different on series 2

Also you'll get twin airbags as standard in series 2, '93-'94 driver's airbag option, '95 driver's air bag standard. Not sure about ABS, I think it's an option on series 1, standard on series 2 (Don't quote me on that one!!)

Also some electrical components on engine are different, eg. coil packs

There might be more but that's what I have discovered anyway....

Hope it is of some help,

Cheers

a plastic wheel turbo? are u sure? wouldnt that...melt? hehe

..i think the ceramic turbo is stock in ALL SKYLINES series 1 & 2.

anyways, im buyin a series 2 in abt 2months, and i definately like it more than the series 1 look..plus its a newer car..if u can afford it $25-32000.

I think the plastic wheel thing is true. Must've been a cost cutting exercise, but some say it has a positive in that it spools quicker? JAGR33 covered the differences pretty well I think. As for ABS, it isn't standard in Series 2 either, in fact it's still quite rare to find ABS and sunroofs on Series 2s. My friend has a Series 2 with a sunroof (he was lucky) and no ABS. I prefer Series 2s personally, they look more modern.

Hope this helps.

Originally posted by V-meister

I think the plastic wheel thing is true. Must've been a cost cutting exercise, but some say it has a positive in that it spools quicker? JAGR33 covered the differences pretty well I think. As for ABS, it isn't standard in Series 2 either, in fact it's still quite rare to find ABS and sunroofs on Series 2s. My friend has a Series 2 with a sunroof (he was lucky) and no ABS. I prefer Series 2s personally, they look more modern.  

Hope this helps.

it not a cost cutting thing to have a plastic turbo wheel, it spools alot quicker and it very high strenght plastic that would never melt but rather just break off if pushed 2 much!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks everyone for the replies and suggestions. Got the seats out (hoping I could find some existing grommets but no such luck). By tapping and measuring etc. I could figure out where I could drill through if needed. But first I borrowed an inspection camera and managed to go through factory holes in the chassis rail and could see that the captive nut was holding steady which is why it could retighten. So it was indeed a stripped section of thread, so I applied downforce by levering the bolt head with a screwdriver and went slowly back and forth until it came out. Camera helped a lot cos I could monitor that the captive nut was holding tight. Now I just have one very seized main subframe nut to tackle 😅
    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...