Jump to content
SAU Community

Wierd Clicking Noise When I Start The Car

justin911

By justin911,
in General Maintenance

 Share

Recommended Posts

justin911 Grand Master

justin911

Posted
Posted

hey ppls

For the last week or so when i start my car it makes 2 wierd clicks right before the motor is actualy running.

Like i turn the key, it makes the choking noise for a couple of seconds like normal then right before the engine is on and running it makes 2 wierd metal sounding clicks.

You can only hear it inside the car from the drivers side and im pretty sure its coming from somewhere near the wheel. Its not causing any issues it just never did it before and i dont want it to be more expensive to fix later on.

anyone got any ideas.. my dad rekons it might be the starter motor ?but he's an accountant so im to sure....

oh yeah its not the same clicking noise you hear when you get a flat battery and try to star the car.

justin911 Grand Master

justin911

Posted
  • Author
Posted

i was listening to it again a few times just now.

Instead of the normal

rrr rrr rrr rrrrrrrrrrrr noise when i turn on the engine its like

rrr rrr *hit hit* rrrrrrrrrrrr

the rrr indicates the engine noise :D

I had it recorded on my phone pretty well but when i converted the 13 secs to avi it was like 6mb :D

Sumo Mentor

Sumo

Posted
Posted

So this noise is being produced inside the cabin?

Mate, you've just got to get under the dash and chase it :D I've had someone comes in "my cars making a clicking sound" Once you get them to identify the sound you just have to chase it. Last one I found was a violet crumble wrapper in the blower fan, and with Climate control the fan when turned down still just spins very slowly producing a "click click click" sound :D.

Cheers

Sumo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...