Jump to content
SAU Community

Recommended Posts

Ok, did a search and couldnt find info from anyone whose done it...so ill ask the q's ive got here....

I need new rotors and new pads for the r32 gtst. I understand r33 rotors are larger, and that the r32 calipers are up to the task...

So i want to fit r33 rotors (or the largest i can fit :D ) with some freshly rebuilt r32 calipers, using new pads...heres the q's :angry: :

1. Looking at the www.dba.com.au website, can anyone tell me whats the part number of some r33 rotors (DBA4000 series, wiper slotted surface, with kangaroo paw inner)? Or can i go larger in size? (currently have 16" rims)

2. Where can i get the new caliper mount to offset the larger rotor, and do i need one?...also how much should it cost? :angry:

3. Anybody got the workshop diagrams for the r32 calipers, so i can rebuild them? Is it hard to do yourself, or best left to a workshop?

4. How hard is it to swap the rotors etc, yourself?...

:lol: cheers

Link to comment
https://www.sau.com.au/forums/topic/83910-r32-gtst-new-rotors-and-pads/
Share on other sites

1. Looking at the www.dba.com.au website, can anyone tell me whats the part number of some r33 rotors (DBA4000 series, wiper slotted surface, with kangaroo paw inner)? Or can i go larger in size? (currently have 16" rims)

Your GTST will have 280mm rotors, the R33 uses 296mm and R34 310mm. You can run the 296mm rotor, but you will need to use the R33 caliper, did the 310mm ; you will need the R34 caliper.

Problem with trying to use a bracket to offset the rotor that is only 16mm bigger, is well condider the bolt holes are somthign like 12mm, so by the time you drill the two holes next together, there isnt goign to be much meat in the bracket between the hole centres :angry:

So the best bet is sell the R32 caliper and rotor to an S13 owner, and put that money towards soem R34 GTT calipers, then run something like the DBA4000 rotor. (or std rotor if its till in good condition)

Next best bet is grab R33 or R32GTR calipers, check the condition of the seals and pistons etc. And throw on the DBA4000 296mm rotor.

I think the 310mm may need 17" wheels, never really checked though. But if you want to use the R32 caliper you currently have, then let me know what budget you have as i may be able to sort a nice curved vane 324 x 30mm rotor with adaptor to offset your caliper for reasonable price. Are you after slotted, slotted/cross drilled????

2. Where can i get the new caliper mount to offset the larger rotor, and do i need one?...also how much should it cost?

See above

3. Anybody got the workshop diagrams for the r32 calipers, so i can rebuild them? Is it hard to do yourself, or best left to a workshop?

Take the caliper off, and give them a clean..all will be revealed. its not difficult to re-co them and inspect them yourself. Th eonly tricky thing is the grease you use for re-assembly

4. How hard is it to swap the rotors etc, yourself?...

Piss easy, two bolts holf the caliper on, remove brake line if your goign to service the caliper and the rotor should fall off. If it doesnt the rotor has a tapped hole that you cen screw a bolt into to help pry off the rotor if they are rusted on. Just check everything is tight when all goign back together :angry:

Oh...and remove the dust shield while you are there...cut cut cut :D

r32 gtr would be an easy upgrade, straight bolt off, bolt on. all you need is the discs and calipers. I've got some in my shed you can have a look at, quite a bit chunkier than the ones you've got now. I dont want to sell mine, but you can have a look to get an idea how they differ.

Oh, and to make the job all that cheaper, I have a mate that would be interested in your current set up.

I think the 310mm may need 17" wheels, never really checked though.  But if you want to use the R32 caliper you currently have, then let me know what budget you have as i may be able to sort a nice curved vane 324 x 30mm rotor with adaptor to offset your caliper for reasonable price. Are you after slotted, slotted/cross drilled????

Cheers Troy, was hoping you'd see my thread :P

Im interested in the 324 x 30mm rotor with caliper offset mount...but would it need 17" rims to fit as well Troy? I really dont have the cash to upgrade rims atm, but 17" are on the list...or better 16" rims (still undecided on that path). If the will fit the 16" rims, tell me more :D

Im after slotted rotors only...

So the best bet is sell the R32 caliper and rotor to an S13 owner, and put that money towards soem R34 GTT calipers, then run something like the DBA4000 rotor. (or std rotor if its till in good condition)

Next best bet is grab R33 or R32GTR calipers, check the condition of the seals and pistons etc. And throw on the DBA4000 296mm rotor.

So as long as i use the caliper that is normally used with the rotor, you just bolt them up? The caliper mount stays the same?

Oh, and to make the job all that cheaper, I have a mate that would be interested in your current set up.

Will let you know mate, depending on what Troy can do for me.... :D

im using 32 gtr calipers as new 4000 dba discs will be very similar costs for all three options and pads are the same so have a look around for some cheap calipers for sale, it will be cheaper i think to buy some gtr 32 calipers and sell yours then you can use off the shelf rotors with no adapters needed, add some braided lines and good pads and your set. I dont think there is any need for anything larger in a 32 unless you do serious track work

I have noticed with the bigger motor i need to pull it up a tad harder these days :P Pads dont last as long either....

I guess id like an easy upgrade, and the way others have said to sell my gear, then go larger calipers and off the shelf rotors seems nice and easy....

Take the caliper off, and give them a clean..all will be revealed. its not difficult to re-co them and inspect them yourself. Th eonly tricky thing is the grease you use for re-assembly.Oh...and remove the dust shield while you are there...cut cut cut :P

What kind of grease is needed? I think ive got a fresh jar of high temp. grease...HTB? is the one i got...its grey in colour. Will look later to find out.

Why do i want to remove the dust shield?

Dust shield generally means higher brake temps...not a bad thing on the street where you want your brakes to come up to temp quickly and be ready for that one big stop when required. But in spirited driving they get too hot all by themselves so every bit of free cooling is good.

As for the 324mm they do need 17' wheels. Its up to you what you want to do, the 296mm would still be a good upgrade....and i think the bigger rotor gives a nicer feel under brakes...others that have driven the car seem to say that it stops nicely..actually you have driven the old girl, though i cant remember what pads i had in ti back then, i think they were jusr RB74s.

Ill do some numbers and shoot off an email reagrding some options other then the DBA route...

As for the grease...i got no idea, all i know is that it not the sort i put in my hair...

Perhaps ring the local brake joibt and just make out liek you know the stuff; yeh, yeh, just some of the grease for the caliper pistons thanks, yeh you know the one" :P

Actually did a search, and its not exactly the same for the Nissan caliper but its close enough to get you goign, and with the caliper in front of you, well you can easily suss out the rest

http://www.bmw-m.net/TechProc/caliper.htm

http://www.performanceproducts.com/Product...+Grease&type=10

http://www.racerpartswholesale.com/crccaliper.htm

Cheers Troy :P

Looks like i need to use some Castrol GRRB grease... :Castrol GRRB

A rubber compatible castor oil-bentone based grease ideal for packing rubber dust covers of hydraulic and mechanical brakes. Also ideal for use on rubber seals during brake assembly.

http://www.castrol.com/castrol/multiplepro...ntentId=7000402

Sounds the one, years ago when a friend adn i were doing a 200SX i think we used PBR...but sounds like the same thing. Interesting to read that BMW How to suggests just to use brake fluid, makes sense i suppose...i popped a pston out the other week when i was tryign to rush a fluid and pad change, only i forgot to put the pads in, and upon haivn to put th eiston and sealetc ack in, it appeared that Race Brakes had used grease after i had my calipers HPC coated

Interesting to read that BMW How to suggests just to use brake fluid, makes sense i suppose...

But what happens when water gets inside your calipers? Brake fluids hygroscopic(?), & your pistons wouldnt be as "lubed up" after a period of time, then would sieze if not serviced regularly...

Ill stick with the grease still :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...