Jump to content
SAU Community

Recommended Posts

G'day folks

Item:"writeoff" not "statutory writeoff" selling complete car with or without wheels

Location:Fairfield West

Item Condition:1994 R33 non-turbo, automatic 97xxxkms, car was ram from behind at a red light then kissed the ass of the car in front, engine still good, damaged is only on the outside, inside is in immaculate condition, no tear of wear and also non-smoker.

Car still start and drive but not recommneded :D

Price and Payment Conditions:Price is $2500ono complete, front tyres just got changed recently.

Pick up only

Extra Info:think thats all the info for now folks.

Contact Details:Call after 3.30pm 0415 243 245 or 0402 712 813

Photos are below, they are not the best, some are a bit blurry but thats because of the camera not me:)

rego till the end of oct, 2005

Edited by dOOb
Link to comment
https://www.sau.com.au/forums/topic/84972-fs-damaged-black-r33-skyline/
Share on other sites

ok for all you folks who wants to see the damage. in my opion the front can be hammered if you have patients, the rear is a bit more tricky, good for those owner who has a burnt out interior or damaged int. :) or just another skyline for wrecking

post-16344-1124746854.jpg

post-16344-1124746878.jpg

post-16344-1124746892.jpg

post-16344-1124746901.jpg

post-16344-1124746911.jpg

post-16344-1124746921.jpg

post-16344-1124747060.jpg

Edited by dOOb
what size are rims/wheels and price?

bummer ur front bar is busted i need a new stocko, i rear ended someone :D

the wheels are 17s dont know the tyre size, have to check, can't help you with the bar, not the just the front but the rear bar is gone too. :)

dude im intrested wat are the mag sizes but mainly wat are the tyres sizes

dude the wheels are 17s, not sure on the tyre size maybe 225/235 35 17, i'll check

GUYS I'LL WON'T BE ABLE TO SELLL THE RIMS BEFORE SOME ONE TAKES THE CAR AWAY!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...