Jump to content
SAU Community

Recommended Posts

Although the value at which it flashes can be set..

I used to think my knock levels were okay.. then I've seen 90% of people have lower knock readings than me ;) Time for a retune..

i think the knock on the power fc is a load of crap simply because if u go over a bump or pot hole or the road isnt the greatest --(NSW ROADS) the knock level will b all over the place. if u want to be accurate u would get an exhaust temp reading!... my 2cents worth!

i think the knock on the power fc is a load of crap simply because if u go over a bump or pot hole or the road isnt the greatest --(NSW ROADS) the knock level will b all over the place. if u want to be accurate u would get an exhaust temp reading!... my 2cents worth!

I dont think understand how the knock system works ,it's looking for more like harmonics then just bump your a knock to the car. And yes they do work very well or why would a cars like Keir wilsons retain the power fc and hand controller when his running a full metec system (knock detection).

As for knock levels well i think to many people get carried away with the levels as every car is different especially car run fordge pistons and lump cams etc

BUT just concide this that APEXI and i believe nissan don't think there a real issue to you get around 60 knocks as that is when they fire the warning light (not before all they would have set the level lower) all that said most responible tuner will normally stay below 40 or so to give a bit of head room for a bad datch of fuel and or different weather condition to the day of it,s tuning.

pete

I dont think understand how the knock system works ,it's looking for more like harmonics then just bump your a knock to the car. And yes they do work very well or why would a cars like Keir wilsons retain the power fc and hand controller when his running a full metec system (knock detection).

As for knock levels well i think to many people get carried away with the levels as every car is different especially car run fordge pistons and lump cams etc

BUT just concide this that APEXI and i believe nissan  don't think there a real issue to you get around 60 knocks as that is when they fire the warning light (not before all they would have set the level lower) all that said most responible tuner will normally stay below 40 or so to give a bit of head room for a bad datch of fuel and or different weather condition to the day of it,s tuning.

pete

okay i was thinking that knock is the knock inside the engine right as u explained the harmonics well that can change quite rapidly esp if u have hard engine mounts and suspension....is this right ...?

i looked at my knock after going over a bump in the road and it changed...? so in other words it is not an accurate reading at all since it did affect the harmonics in the engine....? and therefor it might not be reading the harmonics in the engine but actually the shock from the bump...?

something on your car is f**ked mate if bumps in the road cause a knock reading. I always monitor knock in my car and it is never affected by road conditions. never. and i will include in this burnouts, drag launches, 4 track days and a fair bit of street driving.

exhaust temp reading is really only a good measure of engine effeciency/AFR and is not as quick to react as a knock meter. they are two completely different things for completely different purposes.

something on your car is f**ked mate if bumps in the road cause a knock reading. I always monitor knock in my car and it is never affected by road conditions. never. and i will include in this burnouts, drag launches, 4 track days and a fair bit of street driving.

exhaust temp reading is really only a good measure of engine effeciency/AFR and is not as quick to react as a knock meter. they are two completely different things for completely different purposes.

ahhaaahah thats a laugh!

so u dont get any knock when going in a pot hole.....?

i find that hard to believe since the vibration is carried through the car...mmmm

but anyways each to your own and ill tell u one thing just had the engine rebuilt ...so its not f**ked!...lololol

im just saying that is not accurate the knock on the power fc.

so u dont get any knock when going in a pot hole.....?

i find that hard to believe since the vibration is carried through the car...mmmm

no i don't unless you are talking about a 3 foot deep cavern (which i can't comment on as i've never driven into one). I have been in potholes before, and a couple of times gone offline a little at turn 4 oran park (big bump there) and yes the knock reading didn't change.

I never said your engine was f**ked i said: "something on your car is f**ked" it may be gearbox problem sending a shock through the crank, or a faulty knock sensor, or knock sensor wiring, or it may just be a shit tune. but i can tell you no car i have ever been in has the knock reading affected by bumps in the road...

no i don't unless you are talking about a 3 foot deep cavern (which i can't comment on as i've never driven into one). I have been in potholes before, and a couple of times gone offline a little at turn 4 oran park (big bump there) and yes the knock reading didn't change.

I never said your engine was f**ked i said: "something on your car is f**ked" it may be gearbox problem sending a shock through the crank, or a faulty knock sensor, or knock sensor wiring, or it may just be a shit tune. but i can tell you no car i have ever been in has the knock reading affected by bumps in the road...

ok ok ok im not going to start answer this if u go over a pot hole or hit the ripple strip at the track and u feel it im sure your engine will feel it....

it may be due to my hard suspension and engine mounts and all the other siffening ..hahah

but im going to argue.

okay i was thinking that knock is the knock inside the engine right as u explained the harmonics well that can change quite rapidly esp if u have hard engine mounts and suspension....is this right ...?

i looked at my knock after going over a bump in the road and it changed...? so in other words it is not an accurate reading at all since it did affect the harmonics in the engine....? and therefor it might not be reading the harmonics in the engine but actually the shock from the bump...?

no that is not right

you need to open your eyes a little and think

If yours is doing this, dont just say the pfc is crap and the knock detection does work may you should be asking why is mine not working (because i can safety tell you that they dont all do what your does) and the knocks and haromics dont have to come from inside the motor as i have seen a exhaust touching the chasis effect knock reading before,(your could be as simple as this).

The knock detection system of the std gtr with apexi pfc is one of the single most helpfull tools in tuning the car a tuner can have(trust me i have know tuned a few).

pete

The reason I asked this question was becuase I have just added a power FC to my GTR and the tune is (out of the box) I was told that they have very advandce timimg so I did a dyno run with results of 11.5 A/F and a knocklevel of around 20.

Was told by a Melbourne PFC tuner that anything around 50 to 60 was bad.But then I was reading in PFC FAQ and it said that anything more than 10 was bad.But it sounds like 10 is a bump steer <_< so all is good B)

Thanks

no that is not right

you need to open your eyes a little and think

If yours is doing this, dont just say the pfc is crap and the knock detection does work may you should be asking why is mine not working (because i can safety tell you that they dont all do what your does) and the knocks and haromics dont have to come from inside the motor as i have seen a exhaust touching the chasis effect knock reading before,(your could be as simple as this).

The knock detection system of the std gtr with apexi pfc is one of the single most helpfull tools in tuning the car a tuner can have(trust me i have know tuned a few).

pete

i found my knock sensor was f**ked sorry guys!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...