Jump to content
SAU Community

Recommended Posts

Hi Guys,

I know I have been a bit dead lately, but that goes with when you get told you have a malignant cyst on your large intestine.

Anyhow, ALL my hot bits are up for grabs, as the PNV is staying as an L series quickie.

If your interesed get in touch.

Dennis

Link to comment
https://www.sau.com.au/forums/topic/85567-hot-bits/
Share on other sites

what have ya got ?

All the bits I have have been well documented on these forum pages.

I was planning an RB30/25DET conversion so everything is pertaining to that.

Trust inlet plenum NEW complete, HKS ext wastegate cast iron exhaust manifold, HKS 40mm ext wastegate 10psi spring, a/mkt 40mm ext wastegate 14psi spring, RB25DE DOHC head complete, R33 GTS25t gearbox, R32 RB20DET gearbox, NISMO short shifter, NEW RB30E harmonic balancer, 1.0mm o/size ACL Race Pistons suit RB25DET (forged), RB25 bottom end, RB30 GTS1 bottom end, R32 245rwkw ECU incl loom, Billet Steel flywheel that will accept 10 in VL Turbo clutch, NEW VL Turbo clutch plate, N1 Oil Pump & Adaptor, VL Turbo Oil Pump, GTR Speedo drive, NEW GTR valve springs, Gates timing belt for RB30 DOHC conversion, RB25 throttle body, 2 x Z32 AFM's, and more.

Link to comment
https://www.sau.com.au/forums/topic/85567-hot-bits/#findComment-1549117
Share on other sites

Trust inlet plenum NEW complete, HKS ext wastegate cast iron exhaust manifold, HKS 40mm ext wastegate 10psi spring, a/mkt 40mm ext wastegate 14psi spring, RB25DE DOHC head complete, R33 GTS25t gearbox, R32 RB20DET gearbox, NISMO short shifter, NEW RB30E harmonic balancer, 1.0mm o/size ACL Race Pistons suit RB25DET (forged), RB25 bottom end, RB30 GTS1 bottom end, R32 245rwkw ECU incl loom, Billet Steel flywheel that will accept 10 in VL Turbo clutch, NEW VL Turbo clutch plate, N1 Oil Pump & Adaptor, VL Turbo Oil Pump, GTR Speedo drive, NEW GTR valve springs, Gates timing belt for RB30 DOHC conversion, RB25 throttle body, 2 x Z32 AFM's, and more.

how much for the lot of the rb30/25 conv setup?

Link to comment
https://www.sau.com.au/forums/topic/85567-hot-bits/#findComment-1549712
Share on other sites

how much for the lot of the rb30/25 conv setup?

The whole conversion???????

RB30E Block, crank, rods, caps etc

RB25DE DOHC 24V Head

GTR Valve Springs

Timing Belt

Tensioner Pulley from RB25DE block

1.0mm o/size ACL Forged Race Pistons

N1 Oil Pump and adaptor or VL Turbo Oil Pump

Standard Inlet Plenum & Runners or Trust Inlet Plenum

R33 GTS25t 5 speed Gearbox or R32 RB20DET 5 speed Gearbox

RB30E Harmonic Balancer

RB25DE Throttle Body

Z32 AFM

RB30ET Billet Steel Flywheel

VL Turbo Clutch Pressure Plate

That's probably about it.

Tell me how much of this conversion you want and I will price it up.

Cheers,

Dennis

Link to comment
https://www.sau.com.au/forums/topic/85567-hot-bits/#findComment-1550178
Share on other sites

RB25DE DOHC 24V Head

GTR Valve Springs

Timing Belt

Tensioner Pulley from RB25DE block

1.0mm o/size ACL Forged Race Pistons

VL Turbo Oil Pump

Standard Inlet Plenum & Runners

R3 GTSt 5 speed Gearbox

RB25DE Throttle Body

Z32 AFM

RB30ET Billet Steel Flywheel

VL Turbo Clutch Pressure Plate......price for above and price for no clutch/flywheel/gearbox

Link to comment
https://www.sau.com.au/forums/topic/85567-hot-bits/#findComment-1550937
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...