Jump to content
SAU Community

Recommended Posts

when the car is on the freeway, the car will drive alright, until it hits bumps in the road, then it feels like the front wheels are being engaged and disengaged over and over...

once it hits the bumps.... it will pretty much surge all the way to my destination.... regardless of road quality... going off the gas will make it go away for a short period... basically its a bitch to drive on the freeway.. everywhere else the car runs fine...

changed plugs gapped to 0.8m and fitted new ngk/ntk el falcon o2 sensor...........

any other suggestions?

Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/
Share on other sites

  muck said:
when the car is on the freeway, the car will drive alright, until it hits bumps in the road, then it feels like the front wheels are being engaged and disengaged over and over...

once it hits the bumps.... it will pretty much surge all the way to my destination.... regardless of road quality... going off the gas will make it go away for a short period... basically its a bitch to drive on the freeway.. everywhere else the car runs fine...

changed plugs gapped to 0.8m and fitted new ngk/ntk el falcon o2 sensor...........

any other suggestions?

Try sticking it in 4wd and see if that fixes it. If it does, then it's an ATTESSA problem, been playing around with the wiring lately?

BTW, Have you checked the ATTESSA fluid level?

:) cheers ;)

Edited by Sydneykid
Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/#findComment-1549081
Share on other sites

  muck said:
could my problem be the rubber?

235x45 front

255x40 rear

235mm X 45% = 105.75mm

255mm X 40% = 102.00mm

That's 3.7% difference, which is on the border line

If the rear tyres are more worn than the front tyres then that would make it worse

265mm X 40% = 106.00mm would be better.

Have you got some other wheels and tyres of the same size that you could test?

:D cheers :(

Edited by Sydneykid
Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/#findComment-1551171
Share on other sites

I reckon you should DEFINITLY put the same size/profile tires on each wheel and take it for a spin to see if it fixes the problem.

And it might be better to try 235/45 all round, as if that works OK you could do that permanently, where you may not want 255/40's on the front..

On a slight tangent, I'm doing a bit of a cleanup at the moment, and will be selling a few tires soon (not wheels). Comes from importing a couple of cars over the years, you get to keep the Japanese tires.., but I've decided I really don't need three entire spare sets for the car…

I've got two mint conditions 255/45 tires, and I think I've several good condition (ie 80%+) 235/45's, so PM me if you end up needing some rubber.. :-)

Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/#findComment-1551688
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...