Jump to content
SAU Community

Recommended Posts

when the car is on the freeway, the car will drive alright, until it hits bumps in the road, then it feels like the front wheels are being engaged and disengaged over and over...

once it hits the bumps.... it will pretty much surge all the way to my destination.... regardless of road quality... going off the gas will make it go away for a short period... basically its a bitch to drive on the freeway.. everywhere else the car runs fine...

changed plugs gapped to 0.8m and fitted new ngk/ntk el falcon o2 sensor...........

any other suggestions?

Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/
Share on other sites

when the car is on the freeway, the car will drive alright, until it hits bumps in the road, then it feels like the front wheels are being engaged and disengaged over and over...

once it hits the bumps.... it will pretty much surge all the way to my destination.... regardless of road quality... going off the gas will make it go away for a short period... basically its a bitch to drive on the freeway.. everywhere else the car runs fine...

changed plugs gapped to 0.8m and fitted new ngk/ntk el falcon o2 sensor...........

any other suggestions?

Try sticking it in 4wd and see if that fixes it. If it does, then it's an ATTESSA problem, been playing around with the wiring lately?

BTW, Have you checked the ATTESSA fluid level?

:) cheers ;)

Edited by Sydneykid
Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/#findComment-1549081
Share on other sites

could my problem be the rubber?

235x45 front

255x40 rear

235mm X 45% = 105.75mm

255mm X 40% = 102.00mm

That's 3.7% difference, which is on the border line

If the rear tyres are more worn than the front tyres then that would make it worse

265mm X 40% = 106.00mm would be better.

Have you got some other wheels and tyres of the same size that you could test?

:D cheers :(

Edited by Sydneykid
Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/#findComment-1551171
Share on other sites

I reckon you should DEFINITLY put the same size/profile tires on each wheel and take it for a spin to see if it fixes the problem.

And it might be better to try 235/45 all round, as if that works OK you could do that permanently, where you may not want 255/40's on the front..

On a slight tangent, I'm doing a bit of a cleanup at the moment, and will be selling a few tires soon (not wheels). Comes from importing a couple of cars over the years, you get to keep the Japanese tires.., but I've decided I really don't need three entire spare sets for the car…

I've got two mint conditions 255/45 tires, and I think I've several good condition (ie 80%+) 235/45's, so PM me if you end up needing some rubber.. :-)

Link to comment
https://www.sau.com.au/forums/topic/85595-surging-problem/#findComment-1551688
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...