Jump to content
SAU Community

R32 Gtr Steering Wheel Size?

danh

By danh,
in Exterior & Interior Styling

 Share

Recommended Posts

xRHETTx Mentor

xRHETTx

Posted
Posted

If Vic there is a minimum size that you can have.

Also, you cant remove an airbag steering wheel (why would you want to?)

And i think you cant go from a wheel with padding to a wheel without padding.

But it will be different in every state

dezz Grand Master

dezz

Posted
Posted
If Vic there is a minimum size that you can have.

Also, you cant remove an airbag steering wheel (why would you want to?)

And i think you cant go from a wheel with padding to a wheel without padding.

But it will be different in every state

are the R33 GTS-T steering wheels smaller than say, a falcon/commodore steering wheel?

Poledra Apprentice

Poledra

Posted
Posted

You're allowed by law, to pass inspection, to have a momo steering wheel because of their safety aspects (dont ask me exactly what, just put it down to they're too good), but they have to be over a certain size. Cant remember exactly the size at the moment, but yeah. Trying to pass a GTR in south australia: have to put EVERY SINGLE THING back to standard... rear wing... brake fuel oil lines.... nose.... suspension... steering wheel....roll cage had to come out.... wheels changed...

Have paid for a standard wheel from a bloke on this site... yet to see it...

Momo is leagle, but size does count. That doesnt mean that if you put your momo wheel back on after it passes that some pissy cop wont do you for it afterwards.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Just had this happen to me too.  R32 GTR.   Also broke "just before going out onto the track" - someone up there is looking out for us... Very scary since I was about to do a narrow street course with zero run-off and curbs everywhere. Many people on here upgrading to billet uprights and R35 bearings?   Or buying new OEM knuckles?  I am not keen to replace with another s/h 30 year old fatigued part.
    • joshuaho96
      Coolant leak?

      By joshuaho96 · Posted

      Top off with distilled water and see what happens. If you keep losing coolant then you know to start looking.
    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
×
×
  • Create New...