Jump to content
SAU Community

Recommended Posts

Where are you based?

I'm reasonably sure Tempe Tyres in Sydney used to advertise RT215s in 18" for less than $500 a corner. The site's been overhauled, so they no longer have the prices.

However, if you're expecting RT215s to perform like a proper Comp-R semi slick, you're going to be disappointed. They're a very grippy street tyre, but even Falken's marketing drones advertise it in the radial section, rather than motorsport class.

i use the RT215s 245/17s, not bad but they are no RE55. if you want semi slicks go the whole hog and get some RE55s or something like that. the RT215s are ok, but the rubber is no where near as soft/grippy as the main semi's out there.

What are they being used for?

One thing people tend to forget is that when semi's are cold they are damn un-grippy. And getting good heat into them on the streets isnt easy.

If its a kick ass street tyre your after then the Aziens are probably the go. I think the new Aziens - the 615's are due out in October. But if its for the track then the RE55's are the go.

What Snoman said.

I assumed from you asking for "semi comps" that you were after a motorsport tyre, for which the RT215s are not suitable.

However, if you're just after something for "daily driving" street use, the RT215s will do a better job. They've got better wet weather grip and don't require as much heat.

Its not impossible to get Comp R semi slicks up to temperature on the street, but generally it'll only be if you go on a fast-paced cruise or whatever. However, every time it rains you're in for an adventure. And the noise will drive you insane.

what im trying to acheive is an all round tyre that will give the best of three worlds?? road , track and strip. is this an impossible dream. i suppose id probably be on the the road 90% of the time though. what do i do spend spend spend on two different sets of tyres or do i buy a good road semi like the rt215s??? would love to hear what you guys think? would 245/40 semis be anygood on the drag strip and the road??

mate if you are on the road 90% of the time i would suggest buying a good road tyre. or if you can afford it buy a 'reasonable' road tyre and a set of semi slicks. I drive on RT215s on the road but i don't do many kms at all so wear is not really that much of a factor. I really think you are better off with two sets if you can afford them, 1 for road, 1 for track/strip.

depends what you are doing.. if you are against true track warriors, they'll have full type R compound and you'll wish you had something a little better...esp in a powerful RWD (like it looks like yours is)

But compared to the occasionals, who who run cheap ass road tyres on the track, then they'll be wondering why you are doing a bit better than they are :) So its all a compromise and what you want to achieve.

You are doing yourself a disfavour running 18's, as even if you go cheap roadies, and cheap track tyres, its still going to cost $$$

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...