Jump to content
SAU Community

Recommended Posts

Hi peoples,

I have just signed up to the site and it is very cool. I have recently purchaced a mildly worked R32 GTS-T which I am very happy with. It is still running the standared intercooler and I want to upgrade to a new/bigger front mount intercooler. Where sould I get this done, (I live in Melb), and should I spend the doe on a custom job or not.

Cheers

JL :P

Link to comment
https://www.sau.com.au/forums/topic/8686-intercoolers/
Share on other sites

ARE do a full kit for the R32 GTSt and from all accounts their coolers are very good. The guy has done many hours R&D getting them right. Its $1178 for the cooler, or about $2100 for the whole kit. Im considering one of these myself at the moment, as is my brother.

check out: www.are.com.au

And i sincerely hope thats not a stock turbo you plan on running 20psi through..... can you say BANG?

Red17

Link to comment
https://www.sau.com.au/forums/topic/8686-intercoolers/#findComment-127820
Share on other sites

Originally posted by red17

ARE do a full kit for the R32 GTSt and from all accounts their coolers are very good. The guy has done many hours R&D getting them right. Its $1178 for the cooler, or about $2100 for the whole kit. Im considering one of these myself at the moment, as is my brother.  

check out: www.are.com.au

And i sincerely hope thats not a stock turbo you plan on running 20psi through..... can you say BANG?

Red17

for $1200 u can get a cooler the size of 900 x 450 x 96 which is a monster and wont fit a r32!

My new cooler is 600 x 300 x 76 and fit real nice in the front of my car!!

AVO are a bit dodgy these days and u will be paying for their name not for the quality of their work.

Use ice they did the fitting of my new cooler and do a great job.

And i hope u aint planning on running the stock turbo at 20psi either!

Link to comment
https://www.sau.com.au/forums/topic/8686-intercoolers/#findComment-129942
Share on other sites

Depends on your goals.

Stock turbo? If so just remove the panel under the front guard behind the stock cooler.

After extra acceleration? Unless you want to track race on a regular basis save your money and don't buy a front mount till you do something with your stock turbo , like high flow it.

Link to comment
https://www.sau.com.au/forums/topic/8686-intercoolers/#findComment-130486
Share on other sites

Originally posted by rev210

Depends on your goals.

Stock turbo? If so just remove the panel under the front guard behind the stock cooler.  

 

After extra acceleration? Unless you want to track race on a regular basis save your money and don't buy a front mount till you do something with your stock turbo , like high flow it.

after putting my new fmic on, and seeing how crap the stock cooler is i dont know y u keep saying not to put a fmic on. The stock cooler is a piece of crap, the air tubes on it are miniature at best and the design of the end tanks is useless. Its so small that at the speed the air goes through it, there is not enough surface area for any cooling to occur, and it was full of oil resisdue. I got a gain on 25rwkw at same boost just by putting a fmic on!

attachment.php?s=&postid=127544

With the stock cooler and 0.8 bar i got 155rwkw and now if u see the red graph i got 165rwkw at on 0.5 bar and the green bar is 183rwkw at 0.9 bar!

Link to comment
https://www.sau.com.au/forums/topic/8686-intercoolers/#findComment-130535
Share on other sites

Mate as far as I know the stock turbo's are ceramic based and if running 13psi (recomended MAX!!) you still have a chance of blowing your turbo!! I would say buy another turbo and FMIC together so save up a bit more and get it all put in at once....

Someone please correct me if im wrong.....

Link to comment
https://www.sau.com.au/forums/topic/8686-intercoolers/#findComment-131288
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...