Jump to content
SAU Community

Recommended Posts

Yes you can fit 20" rims on an R33 !! Jonny from Tempe Tyres had 22" rims on his R33 ( no idea of the offset etc. ). I must say though, 20"+ rims and Aussie roads are SO NOT suited IMO. And also ( IMO ), the only car I've seen that looked "correct" with 20"+ rims was a Lexus. But, whatever pushes your buttons.............. ;)

i love my 20s i wouldnt go any smaller

im almost 100% tempe only had 20s on the silver R33 GTR plates were WHYTRY that was the biggest AMEs ever came in

in not sure if they would fit on an R33 GTSt

but i guess it all depends on how much your going to lower it

i think 245s will be too wide for the rear

but as long as you dont drop it on its guts 225 should be ok for the front assuming you have the right offset

get ur 20's dude, they'll look hot, just dont expect them to do any favours for your handling or your wallet ie tyres cost more and wear shitloads quicker on the insides than more regular sizes. After having 19's, I wouldn't go anything over 18's on any car that I ever wanted to actually handle now... except for maybe an X5 or somethin :P

get em dude, or you'll want them forever just like I did!

not really champ

everyone has different tastes some people like 20s and chrome wheels and some dont

i dont have 20s cause im an attention seeker i have em cause thats wat a like and thats the way i want my car to look

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...