Jump to content
SAU Community

Recommended Posts

we live in tamworth and all funds raised will go to get a fusion center up and runing here as for the how will it raise funds we will have to charge an entry fee for the cars and we hope to get some trade displays as i said this is in the early days of planing so any thoughts we be apprecated

Link to comment
https://www.sau.com.au/forums/topic/87998-car-show/#findComment-1590579
Share on other sites

dont forget your cowboy boots. great place.

im sure people would jump at the chance if they knew more!! but like you said your just asking if anyone would be keen, you wont know the numbers till the info and details are up so people can organise accom and time off work, when this is organised im sure it would be a great turn up.

surely one or 2 guy's on the sau team could help this guy out with organising this show for a great cause. good luck!!!!!!!!!! hill climb???? sounds good.

Edited by BIKES
Link to comment
https://www.sau.com.au/forums/topic/87998-car-show/#findComment-1594362
Share on other sites

yeah theres hill climb here (in Tamworth)..its the road to the look-out..i'l get a midnight one happenin' if ya know what i mean :D:) ..but seriously the highways a pretty good drive and our fri sat night lap here's not bad..btw ih8vls is my dad and we both got r33 gts-t's..but mine goes better..hey dad!

Link to comment
https://www.sau.com.au/forums/topic/87998-car-show/#findComment-1605578
Share on other sites

update on car show at tamworth

we are trying to organise a venue that is indoors so we can have a two day show and so we can have trade displays as well we are trying for march next year 4th & 5th so we will be very busy so keep an eye on this space

Link to comment
https://www.sau.com.au/forums/topic/87998-car-show/#findComment-1616612
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...