Jump to content
SAU Community

Recommended Posts

I heard the jap model S15 (manual) injectors which flow 480cc can fit as a direct swap into the rb25det, can anyone verify this? If so would it support up to 270rwkw with fuel regulator? I have all other supporting mods.

Apparently other engines to share this style of injector are the RB25DET, the 1JZGTE, 2JZGTE and the VG30DETT.

Edited by popeye132
Link to comment
https://www.sau.com.au/forums/topic/88162-does-s15-jdm-injectors-fit-rb25dets/
Share on other sites

Yes they are a direct fit. So are USDM Ver 5/6 STi injectors (a little easier to find, usually go for about $USD150 per set of four). The toyota "J" injectors are low impedance, so no good without a ballast resistor. Mazda FD3S primary & 20B injectors will fit with Sard type collars.

So you indeed have some choices !

I looked into doing this once, but I would have had to buy 2 sets of injectors (non of the wreckers would split them) then I was going to get them cleaned and flow tested and use the best 6. Total cost was around $600 (for second hand injectors) - I then decided if I was going to pay that much I would rather spend $700-$800 for new ones rated at 550+

Edited by 4door_Sleeper
I looked into doing this once, but I would have had to buy 2 sets of injectors (non of the wreckers would split them) then I was going to get them cleaned and flow tested and use the best 6. Total cost was around $600 (for second hand injectors) - I then decided if I was going to pay that much I would rather spend $700-$800 for new ones rated at 550+

where did you get them for under $800?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...