Jump to content
SAU Community

Recommended Posts

Macka - I been once, 3 weeks after I got my car!!! On my last runs I started having the power probs I just fixed for the first time.

Don't reckon I got much out of the last session aside from the knowledge that I couldn't drive a greasy stick up a dog's you know what...

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by skyzerr33

can't tell  

the engine bay, can't isolate it seems to be plenum side but i can't tell for sure

Is it a new noise or just the fact that you are listening hard for the first time.

Cheers

Ken

Originally posted by skyzerr33

oh yeah still no pressure at the radiator cap

Troy , stop being so paranoid and worrying about the worst case scenario.

As I said on the phone , it is probably the rad cap has lost pressure and allowing the water out of the overflow.

The murky colour is because you have probably boiled the water when it stopped and it's like giving the block a hot enema , all sorts of shit will come out.

Drive it home tonight , take it easy and don't use the aircond.

Get a new cap in the morning from Auto one , Marlows , Coventry's , whatever.

It's only a cap and the same as dozens of others.

Cheers

Ken

Originally posted by gtrken

Troy , stop being so paranoid and worrying about the worst case scenario.

As I said on the phone , it is probably the rad cap has lost pressure and allowing the water out of the overflow.

The murky colour is because you have probably boiled the water when it stopped and it's like giving the block a hot enema , all sorts of shit will come out.

Drive it home tonight , take it easy and don't use the aircond.

Get a new cap in the morning from Auto one , Marlows , Coventry's , whatever.

It's only a cap and the same as dozens of others.

Cheers

Ken

fingers are crossed

driving like miss daisy all the way home and out to lumpy for the fuel pump

Ohh and drain the water , or get c red to do and stick some new coolant in.

The reason it boils is that without the cap pressure the water will boil at 100deg C

Your car should run normally at about 90 deg C and the 13 or 15 lb cap will raise the boiling point to about 120deg C.

this is why when you open the cap if it's in good nick after driving it , the water will suddenly boil , cos ya dropped the boiling point down to normal.

As yours has no pressure , it will boil easy.

Cheers

Ken

The hissing sound is probably normal pod filter induction or at the worst a vacuum line is off or split.

Just that you are looking and have suddenly heard what has been there all along.

Besides , a blown head gasket does not make a hissing noise , it causes the engine to run rough on startup ( as I said on the phone ) or blows water out of the radiator while it is running or a LOT of bubbles will appear ( some are normal )

Cheers

Ken

Originally posted by adam 32

when coolant says anti-boil - what does this actually raise the boiling point to?

it is the pressure in the radiator that stops most of the boiling.

Anti boil has an additive , like glycol or something , which raises the boiling point slightly , depending on the mix.

Cheers

ken

Originally posted by skyzerr33

sounds good to me ken

i'll stop being a worry wart till the morning. :P

Good , can I close the online free mechanical w/shop and get back to whoring before pwpt60secf arrives ??:P

Cheers

Ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...