Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by macka

Ok i have something to say....

Girls who think that G's are uncomfortable are just being selfish and arent thinking about us guys!!!

2ndly I hate it when they pull there jeans up and we cant see the G :P

DAMN RIGHT..

think about us guys..

but seriously.. how sexy is it yea?

when u can see it?

macka/paul - am chasing an exhaust cam pulley.. after talking with 25GTT i'm conviced that i must have one! combine that with the fact that i'm getting my timing belt done very soon anyway means i may as well do it while the belt is off..

nengun says $185 for the pulley on their website, but brent sent me an email describing both inlet and exhaust for $428?? I assume that postage is about $50. They quoted delivery of one week..

I asked for pricing on the Trust one's shown one the site but haven't heard back yet..

macka/paul

saturday some time i need to go back to the headshop and re-seat the valves then bolt it back together. the guy was too busy today to do it. however being a saturday he aint guah wonah work later than 3-4pm and itll take 2 hrs. so as long as i can get to the head shop by 1-2pm itll be sweet but if we aint gunah get back on saturday by later hat afternoon i cant come down south. i want my car working again

tristans comin over on sunday so anyone whos available at any time the help would be greatly appreciated. im not goin to autosalon.

paul - check ur pm...

macka - am going to have the timing belt of anyhows so thought why not put one on.. so far have afc, itc and more boost.. am going to get dump pipe and fmic - basically very close to the setup 25GTT has.. he seemed to think that the pulley gave him a decent increase in power right over the rev range - so for a couple of hundred bucks I thought I'd give it a try...

cheap power if it works.. :P

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
    • Yes, unfortunately that's the one. Signal was noisy to begin with; after driving once and looking back at the logs I saw pressure constantly swinging between 0-200psi, or staying at 0 randomly for a few seconds. There's a lot of good sensors that share the same look and feel, so don't presume they're all bad. I bought mine for 20$ off Amazon and I should have read the reviews prior, as it's clear they're junk.  I purchased a lowdollerr motorsports sensor. 
    • wedding eh.....I seem to get to more funerals than weddings or christenings these days....
×
×
  • Create New...