Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by 33Spec2

nah nah actually really high standards which sucks most the time coz my mates all get drunk and hook up with mingers and im always the one left thinking hmmmmmm i dont want 2 hook up with any of these chicks!

russ save yourself! it's not as cracked up to be... :D

that's just too sad getting on with drunken chick....yack!

drunken chicks aint my type........

I have to say

Chick smoking and drunken chicks are most ferral! ;) bad ....

i judge by a kiss - if i guys an awful kisser i dont care how cute he is - see ya later - i know that sounds harsh but if u aint enjoying the kiss then u aint going to be enjoying anything else in my opinion. Its my taste tester after everything else has meet my approval ;)

haha my ex was a smoker, chris was a smoker - guy that went to england, joe was a smoker, jeremy was a smoker - ive been out with quite a few smokers! most of them are quite well behaved and just social smokers - my ex never smelt of ciggerettes always smoked outside the house so it enver bothered me - apart from the fact that he had diabetes and smoking had a ten times worse affecton shortenng his life span because of it!

i dont know - i hate guys that go into it like they are trying to fit your whole head in their mouth but then there are the guys that are just way too soft. my ex was the best to date i dont know its just the perfect balance of everything.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...