Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by Micko

Good work Ken - sounds like you had a good weekend.

Tell me - was the rex 'standard' like your car is at the moment? I wouldn't think so somehow...

Catch you later if anyone is still here.

Front mount , bigger turbo we believe and he is good mates with Steve harkins ( evo 3 at Wanners )

Cheers

Ken

Originally posted by SHUTO-BOY

hmm i wonder wheres 60 sec man

He was pretty tired so I think he has headed for bed. Hehehehe

Can't work out all these young people that need Nana Naps all the time.

:)

Cheers

Ken

Oh i was evil. I was loosing big time. No had eye co-ordination lol

So... we went to mini golf at wanaroo batanic gardens, And my little neice and nefew came along ... Tegan has only started to walk and shes soooo cute, well... As troy was about to swing, I told him "Hey troy we have to get married soon so tegan can be our flower girl and be as cute as this... " Lets just say troy didnt play that hole very well.. lol.. it was sooo funny

Originally posted by Kyles

any one wanna know how to distract troy in any kind of sport. exp mini golf..?? hehehehehe

Errr , give him a flash ??

btw , the lawn bowls thing was cos I said to pwp and Niz that Troy played bowls and they said nah , gtfoh !

I said that his pic was one of the first in the Pics and Nics thread ( I think ).:)

hence the sms for confirmation. These young people that doubt my word. Hehehe

Cheers

Ken

yep for sure.

If anyones been up there.. its the hole where you have to hit it against a board and get it into a basket that takes it though to the next part.. well troy kept missing the basket lol...

but it didnt work. I have up 1/2 the way around and looked after tegs, and i think leighton whos 3 beat troy hahahha...

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...