Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Ken - my car is making 264rwhp (2wd) on steve's dyno before it hits the speed cut at around 6900rpm.

Basically as gav said he hasn't picked up much more power with the PFC he is using now - but I'm sure that will change.

I got 220 at all 4 with 1 bar on Hendos and 260 at 1.2 bar ( I think). That was on std puter and it ran fine.

So the reason it makes more power in the Mines is the lack of speed cut allows a higher rev ?

To see if there is any advantage , see what it gets at 6900rpm.

Cheers

Ken

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Ken - wtf is 1.5 or 2 way - I'm sure I should know, but can ya tell me anyway:)

Not 100% but 1.5 supposedly locks under power and unlocks on coast ( ie lifting off around a corner. )

2 way locks on power and coast and opens at neutral throttle.

Cheers

Ken

Micko Veteran

Micko

Posted
Posted

Nice...diffs sound good.

I am going to plug the puter into my car & test it out. The deal atm is $200 exchange with my standard one. It's gotta be better I would think, but I will make sure.

Even though I don't know gav very well, I feel confident that if things weren't right he wouldn't hang me out to dry.

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Nice...diffs sound good.

I am going to plug the puter into my car & test it out. The deal atm is $200 exchange with my standard one. It's gotta be better I would think, but I will make sure.

Even though I don't know gav very well, I feel confident that if things weren't right he wouldn't hang me out to dry.

Nah , would be cool .

Cheaper than paying for a speed cut but be aware that some of the Jap chips are a bit aggressive with the timing and our third world octane fuel.

Cheers

Ken

Micko Veteran

Micko

Posted
Posted

Ken - if youre still there...

A mate is gonna make me some front pipes on sat. Gonna cost me for the stainless piping (should get change from $100) & a bottle of the sphincter of the universe. Making 2.5" to 3". Interesting to see if there is any improvement, but for that price it's gotta be good value:uh-huh:

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Ken - if youre sttill there...

A mate is gonna make me some front pipes on sat. Gonna cost me for the stainless piping (should get change from $100) & a bottle of the sphincter of the universe. Making 2.5" to 3". Interesting to see if there is any improvement, but for that price it's gotta be good value:uh-huh:

Me thinks without the dumps , it's gonna be very marginal.

Make sure you give him the the sphincter of the universe AFTER the job.:D

Btw , R33 GTR dumps are bigger and flow better than R32 GTR dumps.

useless fact 1

Cheers

Ken

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

BTW Ken - what turbos were you running at 1 bar or higher?

Thought you said that was too much for the standard jobbies?

Gav is running 1 bar at the moment - I wouldn't mind doing the same.

Hendo was doing his usual more is better.

I said that now you have had a play , turn the wick down cos they is only std.

Cheers

ken

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...