Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Ken - my car is making 264rwhp (2wd) on steve's dyno before it hits the speed cut at around 6900rpm.

Basically as gav said he hasn't picked up much more power with the PFC he is using now - but I'm sure that will change.

I got 220 at all 4 with 1 bar on Hendos and 260 at 1.2 bar ( I think). That was on std puter and it ran fine.

So the reason it makes more power in the Mines is the lack of speed cut allows a higher rev ?

To see if there is any advantage , see what it gets at 6900rpm.

Cheers

Ken

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Ken - wtf is 1.5 or 2 way - I'm sure I should know, but can ya tell me anyway:)

Not 100% but 1.5 supposedly locks under power and unlocks on coast ( ie lifting off around a corner. )

2 way locks on power and coast and opens at neutral throttle.

Cheers

Ken

Micko Veteran

Micko

Posted
Posted

Nice...diffs sound good.

I am going to plug the puter into my car & test it out. The deal atm is $200 exchange with my standard one. It's gotta be better I would think, but I will make sure.

Even though I don't know gav very well, I feel confident that if things weren't right he wouldn't hang me out to dry.

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Nice...diffs sound good.

I am going to plug the puter into my car & test it out. The deal atm is $200 exchange with my standard one. It's gotta be better I would think, but I will make sure.

Even though I don't know gav very well, I feel confident that if things weren't right he wouldn't hang me out to dry.

Nah , would be cool .

Cheaper than paying for a speed cut but be aware that some of the Jap chips are a bit aggressive with the timing and our third world octane fuel.

Cheers

Ken

Micko Veteran

Micko

Posted
Posted

Ken - if youre still there...

A mate is gonna make me some front pipes on sat. Gonna cost me for the stainless piping (should get change from $100) & a bottle of the sphincter of the universe. Making 2.5" to 3". Interesting to see if there is any improvement, but for that price it's gotta be good value:uh-huh:

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

Ken - if youre sttill there...

A mate is gonna make me some front pipes on sat. Gonna cost me for the stainless piping (should get change from $100) & a bottle of the sphincter of the universe. Making 2.5" to 3". Interesting to see if there is any improvement, but for that price it's gotta be good value:uh-huh:

Me thinks without the dumps , it's gonna be very marginal.

Make sure you give him the the sphincter of the universe AFTER the job.:D

Btw , R33 GTR dumps are bigger and flow better than R32 GTR dumps.

useless fact 1

Cheers

Ken

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Micko

BTW Ken - what turbos were you running at 1 bar or higher?

Thought you said that was too much for the standard jobbies?

Gav is running 1 bar at the moment - I wouldn't mind doing the same.

Hendo was doing his usual more is better.

I said that now you have had a play , turn the wick down cos they is only std.

Cheers

ken

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Have you flushed the initial fluid yet? It should look like a rainbow unicorn shat glitter into it. 2nd or 3rd fluid change is when you party.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • PranK
      Most women will agree that parking is the most taxing part of driving

      By PranK · Posted

      Go back and watch the video again... 
    • funkymonkey
      Most women will agree that parking is the most taxing part of driving

      By funkymonkey · Posted

      Are you meant to double fist them?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
×
×
  • Create New...