Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

OH MY GOD EVERYONE ...... MONDAY I START WORK AGAIN ..... AT THE DEPARTMENT OF INDUSTRY AND RESOURCES ..... AGAIN ..... BUT FOR A DIFFERENT GROUP ..... THE BOSS REQUESTED I SEE HIM ABOUT 15 MINS AGO AND TOLD ME THE NEWS!!!

for once .... with a job do i not land on my feet?????! jobs are one thing i seem to have good luck in!

oh and a chick at the good bye read my palm .... apparently shes NEVER seen a palm like mine!! Im going to have a LOT of indecision in my life and a lot of relationships :)

alex I HERE YA .... about to have another piss up myself - and man i can hardly drive home as it is!!

well Ross i told the IT guy and he went - Phuck them Phuck them all ...... so i guess i'll give an Amen to him :)

Hey there everyone.

I'm in need of help from mechanic types. Is it possible to remove injectors while the fuel rail is still on the car? I've been trying for a while and they don't seem to want to budge. Anyone removed injectors on a RB25DET beofre? Help!

I'm replacing the upper plenum so I have full access to the rail and injectors. The cap on the injector unscews easily enough, and I can get the injector to rotate in the rail, but the injectors are impossible to pull out of the rail.

I think I'll pull the rail out and work on it on a bench.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...