Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

that shit is still beyond me.....how can they expect a creative talent to be a coldfusion/oracle expert........

I wnat to debate this with the government.........I must have studied a wrong units .......or on another planet....

ok I am off to get some pills ....

;)

Al about Being A Loser at the End of "He Thought He Could" (302)

Al to Mrs. De Groot: "So you think I'm a loser? Just because I have a stinking job that I hate, a family that doesn't respect me, a whole city that curses the day I was born? Well, that may mean loser to you, but let me tell you something. Every morning when I wake up, I know it's not going to get any better until I go back to sleep again. So I get up, have my watered down Tang and still-frozen Pop Tart, get in my car with no upholstery, no gas and six more payments to fight traffic just for the privilege of putting cheap shoes on the cloven hooves of people like you. I'll never play football like I thought I would, I'll never know the touch of a beautiful woman, and I'll never again know the joy of driving without a bag on my head. But I'm not a loser. 'Cause despite it all, me and every other guy who'll never be what he wanted to be, are still out there, being what we don't wanna be, forty hours a week, for life. And the fact that I haven't put a gun to my mouth, you pudding of a woman, makes me a winner!"

At the Nudie Bar

from Rites of Passage (616)

Where the music stinks, and they water the drinks, the nudie bar.

Where the girlies dance in their underpants, the nudie bar.

Where you see their butt, and their trap stays shut, at the nudie bar.

Where you can't touch a breast, but you can cave in a chest, at the nudie bar.

Where you look at a thigh, and blacken an eye, at the nudie bar.

Where the beer gives you gas, but the Bundys kick ass, at the nudie bar.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...