Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

can you come and do a dr harry cooper on my dog, and come over and tell me why she is so viscious to men and children - and then train her not to be

tell your hubby to feed her/him

Do the behavioural traning... desensitise him/her

or if male de-sex him-its polly testosteron

or if female must be behaviural problem

my parents messaged me this arvo - they went out n both picked me out a present this morning which is really sweet they seem really excited about this present ... im guessing its not going to make my car go faster but anyway

female, de sexed, never had pups, was abused as a puppy (she is from a refuge), has knife cuts on face and legs..... how do you get that out of a dogs behaviour

Theres your problem ... we had a doberman that had been abused as a pup and she never got over it either. My parents said they would never get another pup that has come from a shelter etc because they just have too many pyschological problems.

Joe WTF areyou talking about?

Joe .... what is this hormone?  

i dont know what my problem is ..... as i get older i seem to have more n more issues.

hahhahahah best line I ever heared all day.... life lesson 101

Hormogonia-> small motile fragments produced by fragmentaion of filamentous cyanobacteria ;used for asextual reproduction :D

Guest
This topic is now closed to further replies.



  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...