Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Sill little kids harrassing me in shopping centre carpark today ...... its like a new generation of mikey's waiting to happen!! "Wow you drive the most awesome car" .... little brat with bike a little too close to my paintwork .... "See that car over there" ...points to dodgy faded green R30 ... "thats a Skyline too" .... "but yours is the best" ...... that was all cool until that started hassling me for change ...."with a car like that you have to have some kinda change" ......me:"Look kid when you get older and you own a car like this - you'll no why i dont have any change!!"

Why do i always get blame for everything :confused:

i'm bright ****ing red.

*mental note to self* put sunscreen on BEFORE you go visit your g/f's horses in whoop whoop when there is no shade*

At least I had fun tormenting LOTS of ants. Found some MASSIVE nests and just annoyed the **** out of them.

Think I'll take a magnifying glass next time :mad:

LOL i do that - we have bees that fall into our pool ..... and so if you take them out an dput them on pavement they just fly into pool again :mad: so i take them out n put them on an ant nest nearby and watch all these little ants attack the bee.

I reckon I had about 2000 ants at the first nest, and I would stick a stick down their main hole, you'd get another 1000 ants come straight out and form like a manhole cover over the hole and about 100 ants climb up the stick and attack it, then I pissed on them and a heap died, it was cool.

The second nest started off with about 10 bullants and I poked the hole and another 50 or so came out, then I fully mashed it up and about 200 came out, so I pissed on them and some of them died too.

Bet you've never done THAT niz :mad:

I'd hate to be a chick (except you'd get to do all kinds of cool things to yourself) and have to piss over an ants nest, cause you'd have to squat RIGHT over it .. At least I can stand back and laugh and not have the little buggers crawl up my feet/legs :mad:

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...