Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by GTS-t VSPEC

Yes, Aaron was a little OTT with his driving at times. Anderson is a good driver and didn't need that. I'm not sure if the RX7 was also to blame, hard to tell from my angle.

Seems that Kerry Wade is still holding on though.

See'ya:burnout:

Matt was on the line but a little behind.

Aaron should have given him some room , hit so hard that the RX7 bounced over the inside kerb and broke the LH lower balljoint which is what put him in the wall.They aren't playing for sheep stations and he will get a reputation like Mitchell where everyone will suddenly gang up on him.

Cheers

Ken

Cheers

Ken

Originally posted by GTS-t VSPEC

Will the Lola be able to make up enough points to win the championship?

See'ya:burnout:

Don't know but I will have to come 2nd or 3rd to keep my chances alive.

Cheers

Ken

Originally posted by GTS-t VSPEC

Hehe, you dirty man Ken:p Don't worry Kyles:D

See'ya:burnout:

Dirty , why so.

You guys discuss the female form and it's banter and flirting.

I discuss it and it's dirty:D .

Cheers

Ken

Originally posted by GTS-t VSPEC

Ken,

Do you know what happened to Shaun Ferrel's car? Seemed to blow alot of smoke all of a sudden.

See'ya:burnout:

O ring on dipstick tube and a slightly over filled sump.

Cheers

Ken

Originally posted by GTS-t VSPEC

It's dirty cause you an old married man:p

See'ya:burnout:

nuff of the old whipper snapper.

Least I got all my points and no yellow. There is something to be said for appearing old and respectable when stopped:p

Cheers

Ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Bummer...yeah i "need" something to "ease" up the work and for my driving it would be enough.    Iam counting the tune "without" turbo. I do not mean "cheap" like something from Temu around 200 USD, "Cheap" is something around 1000 USD? 
    • Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
×
×
  • Create New...