Jump to content
SAU Community

Recommended Posts

Hey Micko , answer the damn question and stop dreaming of Niz.

Has the bas3e timing changed and is there any codes.

* young whipper snapper , bludging in class *

Cheers

old and and grumpy

Ken:D

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Yep - no codes, timing presently about 32 deg.

Must admit that after changing the rear knock sensor on the weekend I haven't had any problems from the sensors

*touches wood*

so let's assume that it was faulty - could always put on the front to confirm, but I might get things right first.

Originally posted by skyzerr33

oh boo hoo ken

cause i can i  will so deal with it mr

ooh , isn't he the keyboard warrior

*no , don't mention warrior or satr wars will return*

Are you at home ??

Cheers

Ken

Originally posted by Micko

Yep - no codes, timing presently about 32 deg.

Must admit that after changing the rear knock sensor on the weekend I haven't had any problems from the sensors

*touches wood*

so let's assume that it was faulty - could always put on the front to confirm, but I might get things right first.

What ?? are you a glutton for burnt arm , scratches and dirty nails.

No codes , base timing OK

Don't phuck with it man !!:P

Cheers

Ken

haha kicking the old man out way to go - its not too bad here cos my parents have a place in bunbury too - so they are only here half the time - but since renovating this house lately they are here a lot more often! I've lived with someone haha its an experience i'll say that!

Originally posted by Micko

You're right - but I'm also a very curious bugger!!!

Plus the front one is a piece of cake to change - I'll show you one day if you like young grasshopper:)

...probably wont bother though cos what difference does it make

Hmm very curious tho.

As I said there MUST have been a prob or the puter wouldn't have come up with a code.

Cheers

Ken

haha no point opening my purse - anything that was in there is on the wheels anyway :P by the mostly stockness of my car its obvious that there wasnt much in the purse to begin with anyway!

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...