Jump to content
SAU Community

Recommended Posts

Hiya,

I am looking into getting a FMIC for my R33 .... My car is stock barring full exhaust and air pod. I want to get the largest intercooler possible without going past the point of sacrificing performance....

I am looking at the two differnet types of HKS coolers.... One is 600x300x65 and the other is 600x300x100 ....

Can I run the larger of the two coolers without making my car more sluggish ( bearing in mind my next step is an AVC-R with boost increase ) or should I settle for the smaller of the two??

I don't want to have to swap if out later on because its not doing a good enough job but I also am not chasing a huge amount of horsepower...

Advice/Opinions welcome???

Link to comment
https://www.sau.com.au/forums/topic/9000-intercoolers-how-big-is-too-big/
Share on other sites

I've got a 700x300x76 and found no increase in lag from a stock one.

Saying that, I think a 100mm thick core is a bit of an overkill.

60mm to 100mm thick core is a increase of 40% in volume (is that right ?? )

Go with the 60mm and save your $$$ for the AVC-R.

J

I've got a custom 700X350X75 and you can feel its adds a little lag on the standard boost. All you need to do is up the boost and you should be fine.

I only got this FMIC as it was selling cheap and I knew it had a good core, otherwise I would have gotten something a little smaller.

Best thing is to have a power goal and have a plan to get the right parts.

Just my 2 cents....

hahah at BK last Saturday with the Westside boys there was a commonwhore that had a truck intercooler. This thing was the biggest intercooler ive ever seen on my life. You could disconnect it while at the beach and use it as a surf board it was just massive.

He seemed to be getting quite abit of attention, i dont know if it was coz people thought it was fully sic or they just thought he was a knob hah.

I have no idea what size mine is but i know its large enuff (and not aligned in the middle properly arggh)

stock turbo?

Going circuit racing regularly?

If the answers are 'yes' and 'no' save your coin for something else, the stock cooler is fine.

If you must have a cooler for no other reason than everyone else has one, then get a small one that flows very slightly more than your peak power goal, with some efficiency.

If you want accelleration there are other things you can do.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...