Jump to content
SAU Community

Recommended Posts

SiksII, what would you say the max boost is that the stock turbo can put out without failing?

i have a front mount and full exhaust, and i run no more than 10psi. u might be lucky at higher boost but i doubt it if you drive it hard.

with stock computer u will find it should run like crap at higher revs at more than 9 or 10psi so there is no point.

then again some stock ecu's seem to be ok with it. in fact i ran 14psi for 6 months (10,000kms) on my old gts-t before realising :D and it was ok but i would not risk it on my new one.

You might have a metal turbine, i do, my car was in good nik aswell so the old owner did it for longgevity in the turbo at high boost, and if the car was looked after in jap it may have been done, 14psi your plugs and coils would need more attention + have you gaped your plugs

"SiksII, what would you say the max boost is that the stock turbo can put out without failing? "

I would suggest that you use the search function..

Your running a 12 year old car, that you from the looks of it have only just purchased. You don't know the history of this car and you think that it's mechanically sound because your an apprentice...

Unless you pull the whole engine block apart and take a look at it your never going to be sure.. most people here run about 10psi.. if you searched you'll find it eaily enough.. if you stuff your turbo, you'll have to fork out for a new turbo + possibly engine repairs..

I doubt your getting to > 180km/h - while on the dyno my car hit the 180km/h limit but didn't even feel like it was, that was in 4th..

As for fuel - everyone on here runs premium fuel that's not going to do crap to save you.. if your car is old or something isn't quite working and you modify it without the correct backups you'll run into issues..

Instead of boosting the turbo - maybe look at getting a new FMIC, an SAFC2, couple of other things, check out the car on the dyno - than wind it up.. that way you can track the A/F ratios and get a decent tune.. at the moment it'll be running very rich, with a proper tune you could prob get as much power out of the stock turbo settings than you just winding it up to 10psi..

Good luck with it..

Links

are you really doing 180 ?

when they are imported they are fitted with an 180km speed limiter as part of compliance, this is easily bypassed and removed, so its possible that its removed, technically u shouldnt be able to top out 4th (on a manual)

which i have never tried, cause those speeds on the road are a little bit stupid u know ...

It has nothing to do with compliance, the 180kph speed cut is a standard function of the ecu from the factory. It can be bypassed easily by cutting wire 53 (speed input signal) on the ecu. Also if you fit a speed convertor so the display is in mph, this will raise the limit to 180mph.

As for boost on a standard turbo, I wouldn't go past 10psi, if you go much higher a standard ecu will increase the fueling and retard the ignition meaning you will be getting less power not more. Also at higher boost you will be running the turbo out of it's efficiency range meaning inlet temps will go through the roof, and the tiny side mount intercooler will not be able to cope. The high intake temp will mean you will very likely get detonation and bye-bye piston ring lands.

Simon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...