Jump to content
SAU Community

Recommended Posts

Heres a group buy for DBA 4000 series slotted rotors.

If I can move 10 sets (40 rotors) then we get the good price ;)

(Note - pairs can be purchased instead of a full set.)

dba4000.jpg

INFO:

All are the 4000 series slotted only.

R32 GTST (RB20DET)

Front (280mmx30mm) - $195.00each

Rear (297mmx18mm) - $195.00each

R33 GTST (RB25DET)

Front (296mmx30mm) - $200.00each

Rear (297mmx18mm) - $195.00each

R34 GTT (RB25DET)

Front (310mmx30mm) - $200.00each

Rear (297mmx18mm) - $195.00each

R32 GTR (RB26DET) non v-spec brembo

Front (296mmx32mm) - $200.00 each

Rear (297mmx18mm) - $195.00each

R32 GTR (RB26DETT) V-spec brembo

Front (324mmx30mm) - $220.00each

Rear (300mmx22mm) - $195.00each

R33 & R34 GTR run the same brakes as the R32 GTR v-spec brembo.

Also Available :

R31 Skyline

Front slotted (non 4000 series) $150.00each

Rear slotted (non 4000 series) $150.00each

350Z (normal brakes)

Front (296mm x 24mm) - $195.00each

Rear (292mm x 16mm) - $205.00each

350Z (brembo brakes)

Front (4 piston 324mm x 30mm) - $220.00each

Rear (2 piston 322mm x 22mm) - $220.00each

More info at the DBA website

SHIPPING:

Postage for 2 rotors direct is $22

Postage for 4 rotors direct is $33

For Melb - Syd - Adel - Canberra - Bris metro (country extra $5)

Postage to Perth - Darwin - ACT - Alice, is a flate rate $44

The rotors are fairly heavy so all will be sent via courier.

FINISH DATE :

Ends - 25th Oct 05.

Payments due - 30th Oct 05.

Im getting 2 full sets (for me and a mate) so we only need to move 8 sets (16 pairs).

1/ gR33ddy - R33 GTST (2xF & 2xR) - PAID - sent.

2/ gR33ddy - R33 GTST (2xF & 2xR) - PAID - sent.

3/ mass_iv - R33 GTST (2xF) - PAID - PAID - sent.

4/ YLD-CHLD - R32 GTR (2xF & 2xR) - PAID - sent.

5/ SirSkyline - R33 GTST (2xF) - PAID - sent.

6/ Pretender - R33 GTST (2xF & 2xR) - PAID - sent.

7/ nisr32 - R32 GTST (2xF & 2xR) - ??????????????

8/ gR33ddy - R32 GTST (2xF) - PAID - sent

9/ private buyer - R33 GTST (2xF) - PAID - sent.

10/ Chicko's GTR32 - R32 GTR (2xF) - PAID - sent.

11/ shif_tea - R33 GTST (2xF) - PAID - sent.

12/ gtrGhosTDoGG11 - R33 GTST (2xF) - ??????????

:)

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

are these the kangaroo paw ones????

if so and for $200 each ill take a set of front discs, not sure if its r32GTR or r33GTST yet....

Yep, they are the kangaroo paw ones.

Link - 4000 series spec sheet

I'll include you in the list of buyers - you can confirm which type you require at any time.

:)

thanks Paul hope we reach 10 buyers, also wats the price without the group buy????

im still looking into what brakes are on my car so i have to go and measure the rotors....

thanks Paul hope we reach 10 buyers, also wats the price without the group buy????

im still looking into what brakes are on my car so i have to go and measure the rotors....

PM sent.

oh and Paul when do you think the due date for payment will be?

Payment can be made at anytime.

A couple of guys will be paying in about a week which is ok.

PM me when you are ready and I'll forward payment details.

Once your payment has been received your rotors will be sent.

Cheers :(

hey i would also like to know the price without group buy on r34 gtt front set

cheers,

R34 GTT (RB25DET)

Front (310mmx30mm) - $200.00each

Rear (297mmx18mm) - $195.00each

Postage for 2 rotors direct is $22

Postage for 4 rotors direct is $33

For Melb - Syd - Adel - Canberra - Bris metro (country extra $5)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...