Jump to content
SAU Community

Recommended Posts

Go and see Japanese Motor Sport, they are experts with skylines bot standard and locked diff. They will also probably be the best and cheapest way to get it fixed if it's busted.

The have both standard and aftermarket diffs in stock.

Mechanicals are wierd in their operation.

You've really got to see a pic of one to understand.

Basically when you apply power (and there is a power difference between the wheels and the motor) the force will push out some rods or spindles things that lock the wheels together.

That puk puk puk puk noise that you hear when going around slow tight corners under power is the inside wheel skipping/spining accross the road.

Remember that the inside wheel will be wanting to spin as fast as the outside wheel but has a shorter distance to travel cause your urning a corner, so the wheel will actaully spin a bit.

Mechanical are good fro drift work, great for track work, and amazing for drags. Basically the most traction you'll get from a 2wd car is a straight line.

Some LSD will swap the power from one wheel to the next which will cause fishtailing - not a good thing. with a mechanical there is always a 50/50 split, even when you start spining the wheels.

God I hope that makes sense ????

J

I think thats your wheels spinning XrSiSt

Thats perfectly normal..

I raced an R33 with a locked Diff.. he wrecked me.. I just kept spinning the wheels (with 255s on the ass) My car had heaps more power then his, but he was able to put his less power car to the ground better.

I say.. if you want a straight line car, and soley want it for dragging... stick with the locker..

But for everyday use, and just a few squirts here and there, the stock LSD item is sufficient ;)

The diff is probably different BUT..

When I had the VS V8 IRS Manual Commodore the diff first started to open wheel a little especially in the wet.

Then idling around corners with no accelerator slow speeds it felt like the diff was a slight locker. i.e the arse end would wobble a bit.

It started to get worse where if i was not perfectly in a straight line and riding the clutch waiting for traffic rolling back then creeping forward a little the diff would make the car have that slight wobble in the arse end like it was a locker and there was also like a slight click clunk type noise when the arse end was wobbling.

Then it all of a sudden was an open wheeler (occasional twin) then the bearings started making a loud grrrrrrrrrrrr on acceleration.

Apparently the bearings where buggered and also the cones which are like the clutch packs or what ever they are..

Replaced everything cost $1000 and the diff was tight enough that on full lock in a servo with the shinny surface the inside wheel would chirp.

Diff then whinned for a little after it was rebuild ?!?

He told me the diff had to be lapped in or somthing.

Anyway it did. whine stopped just before i sold the car thank god...

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
    • That's some really horrible design with the way it's cut/shaped! Is there much damage to the box that failed in? IE, new fork and you can go again, or is it a total rebuild again? Id be trying to build that piece from scratch, and getting some reliefs added in the corner to hopefully stop breakage, and then swapping boxes ASAP, and then doing the same to the currently good working box. I'm assuming hard shifts have not been friendly to it!
×
×
  • Create New...