Jump to content
SAU Community

Recommended Posts

as the aftermerket crank swinging at a bigger angle to create the displacement

so those kit add EXTRA stress to the bearing

Extra stress on the bearings?? we are talking going from 2.6 to 2.8 here, and some of that capacity is gained from the overbore! And you are dealing with a crank that is MORE balanced than the stocker, so id say without the nasty harmonics or vibrations that ive heard people talk about, wouldnt there be less stress on the bearings than a stock rb26 crank (at the same rpm)?

as sydneykid has explained, the square 3litres "have superior rod/stroke ratio (1.79) to RB26s' (1.65), this means less side loading on the rods and the crank."

BUT, as i originally posted i dont want another 3litre thread so lets talk no more of it, i want Jap stroker crank experiences here :)

ok back to topic the three HKS kits as i understand them are

stage 1 (600ps rating)

crank

rods

pistons

$6819.12(deliveried)

stage 2 (800ps)

crank

rods

pistons (but the pistons are coated)

$8,720.87 (deliveried)

stage 3 (1200ps)

crank

rods (22mm judgen pin)

pistons (but the pistons are coated)(22mm judgen pin)

$10,738.65 (deliveried)

in my opinion i think stage 1 is good valve for money full forged stoker kit internals for under $7000 deliveried and i believe it to be capable of much higher hp then rated, coating pistons does make that much of a difference (600 to 800ps) and if i had known earlier about this kit well my current build might have been alot different. I could only see someone going above stage 1 (straight to 3) if you were out to break some hp(dyno) or drag records.

my 2 c

ps HKS conrods are simple awesome

thanks for the RELEVANT post pnblight!

I was just about to go for the stage 2 kit, then remembered that customs will make me pay 25% on top of that cost (10%gst + 15% duty)! Might it slip through?? most probably not, as apparently they are shipped in a reasonably sized wooden crate, and the declaration from nengun (or whoever) will state the value of the parts..

Now youve got me thinking about the step 1 kit. In true Jap fashion it is likely to be underrated. If a combination of stock crank, average quality upgrade rods and pistons can support 600PS, then surely the HKS 'baby' kit can handle 700+ps. I would think they would quote for an extremely long reliable service life supporting 600ps, perhaps circuit car reliable, in which case under street conditions should easy support more. Any thoughts on this??

thanks for the RELEVANT post pnblight!

I was just about to go for the stage 2 kit, then remembered that customs will make me pay 25% on top of that cost (10%gst + 15% duty)!  Might it slip through?? most probably not, as apparently they are shipped in a reasonably sized wooden crate, and the declaration from nengun (or whoever) will state the value of the parts..

Now youve got me thinking about the step 1 kit. In true Jap fashion it is likely to be underrated.  If a combination of stock crank, average quality upgrade rods and pistons can support 600PS, then surely the HKS 'baby' kit can handle 700+ps.  I would think they would quote for an extremely long reliable service life supporting 600ps, perhaps circuit car reliable, in which case under street conditions should easy support more. Any thoughts on this??

from there other kits you can say the crankin stage 1 is good for 1200ps the rods in stage 1 good for 800ps as both components are the same the only factor down rating the kit is the piston coating ,I think a quatity forged piston from HKS would be capable of alot higher ps rating i think the reason for the rating is more to given a justification for the price differences between the kits as who would pay the exact money if the rating were more like

stage 1 900ps

stage 2 1000ps

stage 3 1200ps (for example only)

do you see what i mean

sly33 would it be possible to maybe try buying it for america instead as the free trade agreement (might be cheaper just an idea)

pete

if your paying 10K for parts i reckon it's worth hopping on a plane over there and picking it up yourself. sure it costs $2K but you will save money on frieght (maybe $400?) plus can possibly negotiate a cheaper price (save maybe $500-$1000) and save duties ($1400). you would have to take the crank as carry on (carefully packed in a bag) and put the rods/pistons in your check in. could be a bit ambitous you say but on my last trip to japan i carried over 50kg back. more than 30 of that carry on.

i got funny looks carrying on some springs flying domestic, imagine the looks when they run a fat crank through the scanner! haha

Main problem with that idea for me is that i wouldnt have the time to go over there! But youve got me thinking.. i know guy whos just moved there.

Edited by SLY33

pete, i see what you mean.

but surely there are other diff's than just some piston coating to justify the extra $$? i heard or read somewhere that step1 and 2 cranks are forged counter, whereas step 3 is full billet crank like the JUN one previously mentioned??

not exactly sure..

Edited by SLY33

To quote Tomei on their 2.8 counter weight crank:

"Only 200cc displacement up. It causes dramatic change to RB26. Change is super response and big torque."

As i mentioned earlier, the 200cc extra must make more of a difference than most people would think.

To quote Tomei on their 2.8 counter weight crank:

"Only 200cc displacement up. It causes dramatic change to RB26.  Change is super response and big torque."

As i mentioned earlier, the 200cc extra must make more of a difference than most people would think.

I think you will find (and I may be wrong), that the HKS step 1 kit does not come with conrods, the kit uses 121.5mm rods, so you use your old ones.

Also, all 3 cranks (step 1, 2 and 3) are different, but I believe they are all 12 counter types.

The Tomei RB28 kit includes Arrow rods but uses an 8 counter crank (from the Z tune)

hi mik, ive found that depending on who supplys the kit, most kits come with rods. The only place i found that sold the kit with no rods is Xspeed in Perth.

so is a 12 counter better than an 8 counter? I dont know a whole lot about cranks and only since investigating these kits was the first time id ever heard of a full counterweight crank.

according to the HKS website the step 2 kit is just crank, pistons and rings and is 498 000 yen retail (tax exclusive for use outside japan). the step 3 kit is crank, rods and pistons and rings and is 950 000 yen retail.

it gets frustrating when once source of reliable information says one thing, and another reliable source says another!

heres what nengun offers from HKS, all with rods

HKS 2.8L Kit Step 1 Rated 441kW(600ps)

Compression ratio (Gasket Size)

* 8.70 (t=1.2mm)

* 8.4 (t=1.6mm)

* 8.1 (t=2.0mm)

Parts Included

- Forged piston kit

- Fully forged & balanced counter crankshaft.

-H cross section connecting rods.

* To cylinder block and baffle plate et cetera

Escaping processing becomes necessary.

HKS 2.8L Kit Step 2 Rated 588kW(800ps)

Compression ratio (Gasket Size)

* 8.70 (t=1.2mm)

* 8.4 (t=1.6mm)

* 8.1 (t=2.0mm)

- Forged piston kit (nickel plated & piston surface has a final molybdenum coating).

- Fully forged & balanced counter crankshaft.

-H cross section connecting rods.

* To cylinder block and baffle plate et cetera

Escaping processing becomes necessary.

HKS 2.8L Kit Step 3 Rated 882kW(1200ps)

Compression ratio (Gasket Size)

* 8.70 (t=1.2mm)

* 8.4 (t=1.6mm)

* 8.1 (t=2.0mm)

- Forged piston kit (nickel plated & piston surface has a final molybdenum coating).

- Fully forged & balanced counter crankshaft.

- H cross section connecting rods.

* To cylinder block and baffle plate et cetera

Escaping processing becomes necessary.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...