Jump to content
SAU Community

Recommended Posts

Hi Guys

this car would suit collector and is one of the best you will find

Price $27,500

Kilometres 56,000

Body 2 door Coupe

Colour gunmetal grey

Interior Colour black/grey

Transmission 5 speed Manual

Engine RB26DETT

This car has tien electronic suspention, hks boost controller, stainless steel exaughst system with twin dump pipes, hks turbo's. These tasteful mods compliment this godzilla. Car's body condition is in very good condition and the interior is immaculate. definatley one of the best on the market and would suit a collector/enthusiat. Please call either 0422023478 or 0407564971

or you can email us [email protected]

1989bnr32%20001c.jpg

1989bnr32%20002c.jpg

1989bnr32%20007c.jpg

1989bnr32%20008c.jpg

1989bnr32%20009c.jpg

that is 27500 compliance and more then likley registered if you would like to talk more about the car and the small details please call tonight after 6.

thanks greg

that is 27500 compliance and more then likley registered if you would like to talk more about the car and the small details please call tonight after 6.

thanks greg

thanks for that.

just one more qu, was the car brought in under teh 15yo import rule?

if so, would u be prepared to sell it as is?

//gorjan

yes we would be prepared to sell as is, as the car was bought in under the 15 yo rule

thanks greg

also nice to talk to you gorjan

sounds good.

like wise.

are you able to talk if i give u a call?

//gorjan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...