Jump to content
SAU Community

Recommended Posts

Heres my Lozza

Some new Pics at bottom of Page

C33 Nissan Laurel

Inspection Front Bar

Wonder Side Skirts & Rear Bar

Flared and Rolled Guards

Deep Dish Wheels (16" Front - 17" Rear)

Xenon HID Head Lights - Very Bright Artic Blue

RB25det Engine Conversion

5 Speed Manual RB25det Gearbox

Trust TD06 Turbocharger

GTR Frount Mount Intercooler

HKS Air POD

Oil Catch Can

Aftermarket Dump Pipe

Full 3" Mandrel Bent Exhaust w/ Cannon

GTR Fuel Pump

Greddy Type R BOV

Remapped ECU

Turbo Timer

Pivot Air Flow Converter

Triple Layer Radiator

Twin Thermo Fans

Twin Plate Clutch

Nismo 2 Way LSD

Short Shifter

Kei Office Coilovers (Everything Adjustable)

Rear Adjustable Camber Links

Cusco Front and Rear Strut Bars

Cusco Front and Rear Swaybars

5 Stud Conversion All Round

GTR Brakes

Slotted Rotors

8 Point Roll Cage

Boost, Water Temp, Oil Temp & Oil Pressure Gauges

Nardi Personal Steering Wheel

R32 Seats

Raised Bonnet

Zip Ties in Front Bar

Power

Made 300rwhp @ 1.1 Bar

Pictures

power_47.jpg

44_743.jpg

Edited by j_insoll
Link to comment
https://www.sau.com.au/forums/topic/92608-nissan-laurel-rb25det/
Share on other sites

konect - Yes the car is RWC and Registered, driven probably 2 or 3 Times a week.

jimbeam - I did not fit the TD06, a Japanese Guy did..........

Sky80 - Lier - I fitted an Oil Catch Can, Bride Seat, and put zip ties in the front bar. :lol:

But yes all the work was done in Japan

very nice... it must be much more relaxing to drift in a Laurel than a cramped up Silvia :D

I've got a TD06 waiting to go onto a RB25DET, so I'm very keen on finding out what engine mods and management you've got to support the beast.

very nice... it must be much more relaxing to drift in a Laurel than a cramped up Silvia :rolleyes:

I've got a TD06 waiting to go onto a RB25DET, so I'm very keen on finding out what engine mods and management you've got to support the beast.

To the Monkey that just so happens to be Funky........... :huh:

Mods are as per posted in the List at the top. Apparently the car has a 'Chipped' ECU, although we have taken a look and dont think it has been touched, though we could be wrong. The Injectors are also Standard RB25det Item. You most likely have the Trust TD06-20g. Mine I 'believe' is the Trust TD06-17c. As far as I know the 20g uses The Single Blade type wheel and the 17c uses the Double Blade type wheel (The 20g is the newer version obviously). I hope im making sense. Im currently running 1 Bar (14.7psi) and It makes full boost at around 4500rpm. Obviously this is a bit Laggy, although I have a feeling the Actuator/Wastegate may be a little bit loose, causing a bit of unwanted Lag. I have had this problem in the past.

With a RB25det, Upgraded Fuel Pump, 550cc Injectors, POD, Frount Mount, Exhaust and a Power FC, you should be able to put out approx. 340rwhp @ 1.3 bar. That would be my guess from what ive experienced with my car. Id guess it to spool up around 4000rpm. But hey I could be wrong!

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...