Jump to content
SAU Community

Taking Off Stickarrhs


Suspense
 Share

Recommended Posts

I wanna take off the shopping list on the side of my car... wanting to know is there any special method? or just peel it off??

Also will my paint below look faded or different? anything a cut n polish wont fix??

PAint colour is white, and excellent condition... :S

Link to comment
Share on other sites

if it was me and my car. i would just hit it with a scraper. and then re spray area. easyiest wway but more expensive.

but other than that patience will be the key.

just start to peel slowly and use something like tea trea oil on it as u go to soften the glue.

so peel a lil put some teatree oil and peel some more and keep going.

if that works no paint comes off, which it shouldnt unless u use a razor blade in parts. then yeah cut and polish no one would kow

Link to comment
Share on other sites

Lotsa hot soapy water first...not boiling water that'll make the clear coat go milky, pour a few buckets full slowly over the stickers then peel off when they're still hot..They'll peel off really easily. It just warms and softens the glue basically. Dont forget...not boliing but pretty hot. If your car is white boiling water wouldnt matter because the clear coat going milky wont show.

Link to comment
Share on other sites

if it was me and my car. i would just hit it with a scraper. and then re spray area. easyiest wway but more expensive.

but other than that patience will be the key.

just start to peel slowly and use something like tea trea oil on it as u go to soften the glue.

so peel a lil put some teatree oil and peel some more and keep going.

if that works no paint comes off, which it shouldnt unless u use a razor blade in parts. then yeah cut and polish no one would kow

Scraper and then respray? The easiest way? Are you f**king kidding me?

Just use a credit card and patience. Then after you have the the main parts of the plastic off use a bit of metho or something and a 100% cotton cloth to rub. Elbow grease, more patience. Don't underestimate how much time and effort this takes but it's the best way.

A tip - get some duct tape and hold it. When you peel little bits of sticker off the car, stick it onto the duct tape .. much easier than fighting with each piece trying to get it off your hand.

Good luck.

Link to comment
Share on other sites

or you can use a hot air gun to remove sticker, get it hot enough so you can still touch sticker, peel from a corner gently.

use turps to remove glue residue left behind, or any gunk remover...

if you get the temp just right it will hardly leave any glue behind at all.

If someone has done a repaint on the job without letting the paint gas off long enough and then slapped a sticker on it there is the potential to pull the paint off, so if you think repaint has been done - be very careful.

paint around sticker will have faded for sure if sticker has been on for any length of time and not been cleaned regularly. If car has been well looked after, the fading or oxidation of paint will be less.

done this heaps of times too, used to work in vehicle sigange industry, put on plenty of business signage as well as removing it when vehicles were sold.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Opened up the cluster to inspect the gauge itself for signs of damage and it looks good. Got curious since that needle doesn't go back to a "neutral" position by itself (it stays in the same position when ignition is off. so I manually moved it to 1/2. Connected it back, turned on the ignition and the needle started moving up! Not sure what's up with that but before that the needle was way down below empty like fully south west. There's always a chance that the needle moved slightly the first time I tried and I didn't notice because of how slowly it moves and how far it was from the markings. I don't know if the current needle position is accurate so I'll fill it up and see where that brings it. I guess I'll try to adjust it manually if it doesn't get to F. Looks like the needle position is relative and not absolute? Thanks all for your help and patience!
    • You're confusing two different responders and more than one issue. The stock Neo ECU boost sensor is used by the ECU for protection purposes. It is essentially only an overboost sensor. It is not used for determining engine load for fuelling or ignition purposes. That task falls solely to the AFM. Any aftermarket ECU that either has an onboard MAP sensor or a plug in one, will use the MAP sensor as the primary load sensor. Or I should perhaps say "can", rather than "will", because some of them have the option of using other primary load sensors. That MAP sensor is not for the same function as the stock Neo boost sensor. The reason I recommended against a plug and play ECU is that they are intended to run a particular engine and usually in the car that the particular engine came in. So, if you have a transplanted engine in a different car, with some parts of the original missing (such as the boost sensor, for example) and therefore likely non-standardness of the loom and its insertion into the car's loom, then it is very likely that you will run into the same problems with needing to fix up wiring to make it work that you would with the stock ECU. And, if doing so for the stock ECU is enough of an obstacle that you start considering a standalone plugin as a solution, it should become clear that the plugin is quite possibly not the solution you'd hope it to be. It would just lead to more of the same type of problem solving work to get it going. In the above paragraph and in my earlier post, the lack of the boost sensor is not critical. It was just used as an example of something that we knew you did not have right, such that the stock ECU would not work. I took that as an indicator of a reasonable probability that there were other related problems hiding there.
    • I can think of two places in my city of <1.5million population that specialise in automotive instrument repairs.Unless you're out in the wilds of Quebec, you have 3 major Canadian and 3 major US cities within the same distance as the single nearest city to mine. Surely there is somewhere you could send it.
    • I never cared for twins but whenever these conversations came up, I always presumed the higher number represented a larger turbo. Learn something new everyday. 
    • Interesting, I've never seen a failure like that before but with the age of these cars and the general questionable-ness of all kinds of parts these days you can't rule anything out I suppose. Boost leak testing the boost control system would've revealed this though.
×
×
  • Create New...