Jump to content
SAU Community

Recommended Posts

Location: Melbourne (outer east)

Item Condition: all in reasonably good nick

Reason for Selling: need space and $$$

Price and Payment Conditions: pickup or i'll post if payment is made in advance

Contact Details: reply or PM here

Have the following parts:

R34 NA 5 speed manual gearbox $500

R33 GTS25t bits:

standard intercooler $50

black front guards $150 each

steering rack and crossmember $70

front radius rods with red nolathane bushes $40 pair

RS*R front springs and struts $120 pair

power steering pump $15

brake booster and master cylinder $60

Heater core $80

Air conditioner core $25

Blower motor $20

Instrument cluster with 64,000km $100

Dashboard garnish that goes around radio, HVAC, air vents, from centre all the way over to the drivers side $100

Most other plastics around the dashboard except the dash itself - make an offer

Dont have the radio bracket :D

I'm going to brisbane around 20th december so I'll be able to drive stuff up if needed.

Cheers

Edited by Bozz
Link to comment
https://www.sau.com.au/forums/topic/93770-r34-na-5spd-gearbox-r33-parts/
Share on other sites

what sort of strength is in those n/a R34 boxes? presumably similar to the RB20DET box i would imagine?

p.s. any chance you're willing to do the wiring for an RB25/30 into VL while you're up in brisbane? was reading some of your posts on PF and saw you did this kind of stuff regularly that's all.

what sort of strength is in those n/a R34 boxes? presumably similar to the RB20DET box i would imagine?

p.s. any chance you're willing to do the wiring for an RB25/30 into VL while you're up in brisbane? was reading some of your posts on PF and saw you did this kind of stuff regularly that's all.

Yeah its similar outer dimensions to an rb20det box.

re the wiring, i can do it but will need to sort out dates accurately later in december.

re the instr cluster, i replied to the pm

cheers

hello there

I have a r33 series 2 GTS-T.

do you sell the

1. front lip

2. rear speaker bracket... have a look at the picture

3. the cover that covers up the battery compartment in the boot

please let me know. thanks

post-22619-1131367978.jpg

3.jpg

4.jpg

5.jpg

6.jpg

7.jpg

The drivers side 1/4 is perfect, the passenger side is missing the GT badge and not as good condition. I'll sell the passenger side panel for $100

Edited by Bozz
Hey mate, With the R34 gearbox will i need to change my tail shaft, i have a r33 skyline rb20e....

Dayne

Absolutely no idea :D

I'd imagine the answer is the same tailshaft will fit but I've never swapped a 31/32/33 gearbox for an R34 one.

The only different gearbox I know of is the GT-R, VL turbo commodore and R33 GTS25t gearbox that uses the huge tailshaft yoke

will the gearbox stright fit into an r32 gts or is there modifying involved also r u negotiable with price?

I suspect it will bolt straight in but you may need a new clutch slave cylinder. I could be wrong though.

Offer a price via PM and you may be lucky and get it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...